Recent content by cgisharon

These are my new numbers. Should I add the Washing Soda now or will it throw my PH and TA more out of wack? Also should I go ahead and turn on my SWG since adding the bleach or wait until it's regular schedule tomorrow/ tonight? Feeling a bit overwhelmed! New Numbers: FC-3 PH-7.5 TA-40 TH-200...

These are my current readings about 3 1/2 hours since refill with pump running. Adding the Acid and bleach now. Separately as read in other post. Will post new numbers tomorrow. Thank you for any further direction. Salt is test is just below 5.3 (2000 ppm). FC-2 PH-8.4 TA-120 TH-200 CYA-30 to 50

The 30-50 was prior to refilling. Before the first refill I was registering 100 according to pool store testing. I was giving the water some time to circulate before retesting. Will test and repost. Thank you.

Looking for guidance after draining pool twice to lower CYA. Just finished refilling and not sure what's next. I received a bad gallon of stabilizer, since I had never used didn't realize there was a problem until it was to late. About halfway thru the gallon it was solid. Can't totally blame...

Leaking & Plunger Valves Stuck Have a couple of problems and don't know where to start. Intex old style Plunger valves are stuck and leaking around connection. Also leak from Pro-Series modification connection on bottom. Looks like the leaks are from the hose connections on the intake side...

My new levels: FC-0 PH-8.4 TA- 80 TH- 200 CYA-30 Went to HP to purchase the Muriatic Acid and came back to a busted pump hose:(. Just got back with the replacement hose and installed. Refilled water lost and test results above! My FC is now 0. Any guidance, what do I need to do next? Thank you...

Thank you all for your help. I retested this morning and my new levels are: FC-3 PH-8.4 TA- 80 TH- 200 CYA-30 I did some reading and think the noise is due to my water level being at the minimum. Going to raise it just a bit and see what happens. Headed to purchase the Muriatic Acid now. Will...

Test results after shock FC-10 PH-8.4 TA-80 TH-200 CYA-30-50

After two failed attempts (two leaky pools), now have a spanking new Pro-Series. With all the rain here it's been impossible to get anything done until this evening. I altered an original pump from one of the other pools (same style) to use my Intex hoses. Very slight leak from one of the...

Nice and level. I got in and pushed all the wrinkles that would move outward. Some of the wrinkles are in the pool permanently. Not sure the cause. Walked around pool after the rain no leaking water seen. It's been raining for days here so I'm not surprised there was moisture in the sand. Can...

Hello. Have a used 15'x42" Polygroup, Summer Escapes Metal Frame Pool. Have base level, sand and tarp. Finished pool setup but, rain came before I could get it smoothed out. There's a little rainwater under the pool. Can I continue filling or do I need to wait? Water was too heavy to lift so, I...

Finally got her patched and filled :D. It's definitely been a learning experience. Missing the plug to stop the water prior to attaching hoses. Anyone know the diameter of the plug needed for the 18'X48" Easy Set Round Pool? Thanks!

Well, after closer inspection my pool has a lot of pin holes. Patches seem to be holding okay. My top ring is also still holding air. Searching forum fo more info since I have so many tiny holes to patch. Will check back in! Thank you for your help. Really glad to find this forum.

That's not going to work to large of an area and it's too dark to really see. As you said that's the price of "FREE". Let me know if any suggestions!

There's only about 1 1/2 inch of water in it so I turned it off. Lifted the corner and the wet spot was limited to a small section. Could I maybe rub a small amount of bubbles on it and use the inflator to see if I get any bubbles?