Search results

It finally worked when I reset the chlorine. It may have been the switch that was stuck in an in-between position. Your help has been absolutely incredible. Thank you so much for your time and wisdom. You have no idea my frustration these past 7 days. As for the valves, I didn't build the pool...

It goes from flashing No Flow to Generating (for about a minute) and then goes to solid NO FLOW and INSPECT CELL. We've had the valves in same position since we opened on 5.12.23 so I'm kinda lost.

That did the trick! Awesome advice! The power is now on but the NO FLOW light is continuous and so is the INSPECT CELL. But it's a brand new cell.

Hey everyone. My battle with my SWG continues. The problem is that there is no power light, no generating light, but there is a no flow light when the pump is first turned on. It also gives the diagnostic readings. 2800, 82, 14.6, 0.00, 68P, - 0, AL - 0, r 1.59, t-15 I've replaced. 1. New...

I just ran through my diagnostics and everything is normal except for cell voltage. It reads 15.4. From what I read, it should be 30-35 when off or 22-25. Does this confirm that my T cell is dead or do I have other issues?

I've had this about 7 years. Today, I tested pool and noticed chlorine dropped so I went to turn my chlorine up from 67 to 72. Inspect cell light came on briefly and then everything went black. The panel still works (reads 3000, 72 p, etc etc) and the no flow light works when you turn the pump...

I've set it up that way and the water doesn't seem to be getting much warmer. 0.4 degrees in about 1 hour or more (from 65.5 to 65.9). It's also only about 67 degrees and cloudy outside though.

Thanks for the great info. If we left the heater bypass valve open we'd be mixing heated pool water with non-heated? I've owned this pool (2nd owner) for 9 years and I believe the middle vertical valve has been open in previous seasons.

Pic is the input and output from the heater. I turned the top valve off and tried to turn pump on but lost prime in pump. Once I opened the valve and got prime back to pump, I turned on the heater and shut the top blue valve off again. The heater kept working. I'm not sure if pump losing...

The skimmer closest to the shallow end gets great suction, but the other skimmer doesn't and I'm not sure about the main drains (too cold to get in right now). I'm thinking that one of the returns goes into the heater? I forget if the water goes from the heater straight back into the pool or...

I used a new pool company to open my pool this year, and I don't believe they did a good job. My concern is the valve opening or closing position (circled in red). Is this correct to leave both of these open? I'm thinking I need to leave both open, right? Or why else would I need to close...

Yep, the floor of the pool is much smoother now. The pool guys redid a pool mix before they put the liner in. I did order the parts. I had to call Maytronics to get some of the parts numbers. I looked at my Dolphin. The middle roller (clear one) has half of the "rolling pieces" missing...

Thanks for the info. This is my first pool and I always felt that the floor of the pool was real gritty and had a lot of little tiny bumps. When the pool company came out to change it, they said it was not normal that it was like that, but I'm not sure what caused it. The previous owner was...

Got it. That's the same website that I found while trying to troubleshoot. Thanks for all of the great info. I guess it's time for me to give the M5 a tune-up. - - - Updated - - - Patrick. One last question. I had a lot of tiny holes in my pool liner (6 years old). Do you think the...

Patrick. Thanks. I replied to that thread. I had the same identical problem.

Patrick. This is great. This is exactly what I am having trouble with! Identical issues! Did you order your parts online or at your local store?

Hey everyone. I have a Dolphin Supreme M5. I am 2nd owner of this 6 year old pool and Dolphin. The previous owners did not take good care of anything. My Dolphin does not stay in the shallow end and has a tough time going up walls. After some Internet browsing, I think it maybe a "Foam...

I've never thought to put the CYA socks in a bucket and let it dissolve that way. Then pour the bucket of CYA around the pool, right? That would save me a ton of time since I've just started filling my pool and it will take me a few days. So when the pool gets filled up, the CYA bucket should be...

So leave the SWG off and turn on the pool pump/filter for about 8 hours a day until I get the CYA stabilized?