Search results

  1. ChasPro

    At first sign of algae ...

    Yeah ... I have 6 gallons... probably enough for me and my neighbor to close our pools this year. Thanks for the link to review.
  2. ChasPro

    At first sign of algae ...

    Thanks everyone for your input. The pool cleared up by August 15 and then, since it was cooler here in Buffalo, took another 10 days or so to get the FC down from 24 ppm to 12 ppm. While that was happening I repaired my SWG and got that running again through the calibration, etc. Ran the T-5...
  3. ChasPro

    AquaTrol RJ Lights Go Out Just After Turning On Generator

    Success. I chose to remove/replace the thermistor instead of snipping off and soldering to the existing leads. I made sure to have a soldering iron with enough power to heat and melt the existing solder in the larger heat-sinking pads. I bought a soldering kit ... but found that the provided...
  4. PXL_20230820_221800881.jpg

    PXL_20230820_221800881.jpg

  5. PXL_20230820_222111656.jpg

    PXL_20230820_222111656.jpg

  6. PXL_20230820_222156314.jpg

    PXL_20230820_222156314.jpg

  7. PXL_20230820_222445455.jpg

    PXL_20230820_222445455.jpg

  8. PXL_20230820_224709232.jpg

    PXL_20230820_224709232.jpg

  9. PXL_20230820_221728524.jpg

    PXL_20230820_221728524.jpg

  10. ChasPro

    AquaTrol RJ Lights Go Out Just After Turning On Generator

    Well, the Hayward diagnostic guide also said to test the transform output blue/white and grey/violet pairs for resistance... and, unless I'm doing that wrong, they were both 0 instead of the 2-3 ohms expected ... so it could [also] be a transformer. TBD. Thermistor first.
  11. ChasPro

    AquaTrol RJ Lights Go Out Just After Turning On Generator

    Got lucky that the unit was misbehaving on the bench today. Check out what happens when you squeeze a thermistor ... NOTE: Don't use your hand if the unit has been on for a while ... the thermistor gets too hot to touch under normal operating conditions. Others have shown use of a large clip to...
  12. PXL_20230814_221201114.TS_exported_5509.jpg

    PXL_20230814_221201114.TS_exported_5509.jpg

  13. PXL_20230814_221201114.TS_exported_14046.jpg

    PXL_20230814_221201114.TS_exported_14046.jpg

  14. ChasPro

    At first sign of algae ...

    I wasn't testing multiple times for the results ... I was trying to figure out how to get a consistent and valid measurement by repeating the measurement when they didn't make sense. I'll be sure to take circulating measurements from now on for at least consistency on that front ... Thanks for...
  15. ChasPro

    At first sign of algae ...

    Well, I'm not running the pump 24/7, so something will be needed to compensate. I bought a new T-5 in 2020. My SWG unit is failing right now (I'm chatting about that on another thread), most likely the thermistor. If the cell is also failing for some reason, I'll be sure to consider the upgrade...
  16. ChasPro

    AquaTrol RJ Lights Go Out Just After Turning On Generator

    I had seen the advice to replace thermistor on many posts. I just wanted to be sure I was going through the troubleshooting steps and making the right repair before committing to replacement. The bench testing done last week seemed not to point there ... but the strange behavior this morning...
  17. ChasPro

    AquaTrol RJ Lights Go Out Just After Turning On Generator

    Cell S/N: 3E20154... purchased just as the pandemic broke out, as my previous cell was already 8 yrs old. Using an analog meter, so approximations. Base voltage on main board matches display at 29.5v. Other test points are near 5v as expected. That's at a bench, simply powered up. Nothing on...
  18. PXL_20230813_122742815.jpg

    PXL_20230813_122742815.jpg

  19. PXL_20230708_210948792.jpg

    PXL_20230708_210948792.jpg

  20. PXL_20230708_210927064.jpg

    PXL_20230708_210927064.jpg

  21. PXL_20230708_210428527.jpg

    PXL_20230708_210428527.jpg

  22. PXL_20230708_210411539.jpg

    PXL_20230708_210411539.jpg

  23. PXL_20230708_210345528.jpg

    PXL_20230708_210345528.jpg

  24. ChasPro

    At first sign of algae ...

    My SWG has been out of commission for a month. All liquid Cl from pool store since. (No, haven't pivoted to Walmart bleach yet ... I'm a slow ship to turn ...). Only thing added to the pool besides the documented Cl has been the rain and any accompanying tree debris. Last evening: Vacuumed and...
  25. ChasPro

    At first sign of algae ...

    Advice was to use 1 heaping dose of DPD powder, and then let drips fall naturally from the bottle without squeezing, and swirling tube constantly. Did all but the natural drips ... nothing was dripping out without a little encouragement. So, each drip I went through the whole cycle of...
  26. ChasPro

    AquaTrol RJ Lights Go Out Just After Turning On Generator

    Symptoms: My swg “generating” light comes on then both "power" and "generating" go off. I have power to the system with "power" light on. As the generating switch is turned from Off to Auto, the "generating" light comes on then voltage drops and both lights go off. The only way to get the...
  27. ChasPro

    At first sign of algae ...

    Yes, I am doing all of that as described, except the part about not squeezing the bottle. I'll do that going forward. My measurements were consistent and predictable throughout this whole period until (a) new dpt chems, (b) more rain than earlier in summer. Would either of these result in the...
  28. ChasPro

    At first sign of algae ...

    Having trouble getting consistent FC measurements... New test chems all around... What's happening? ========================================== ChasPro01 ------------------------------------------ Build Type: Vinyl Volume: 13500 gallons...
  29. ChasPro

    At first sign of algae ...

    I was a little leery of the final ONLT and clarity, so I SLAMed another day. Then heavy rain made the next night's ONLT suspect. Went one more day to have a full night without rain. Much clearer this morning than yesterday... SLAM an extra day or more if you think you're clean. Possibly...