Search results

It coulde be my Voltage meter skills but yah it's contradictory. Anyhow I hooked up a brand new actuator to each output on board....no power/functionality =(. Thank you for repling.

I have a polaris eos 3 control panel with no power to the actuators. coming out of the board I seem to get voltage but actuators have no power? Anyone else encountered this?

Are filter unions interchangeable across brands? Also can you plumb the outside with 2.5” coupler?

I got 2 120 volt pool lights. rather than pay $3-400 for pool specific bulbs. I dont see any reason why some regular LED bulbs wont be ok?

So as fate would have it I drained and refilled 2 pools this week. On both of these accounts the home owner was out of town. So I had to keep going back to check while pool was refilling. Is there a way to fill a huge pool w/o the trickle autofillers that would take 2 weeks?

So when connecting the control panel to the circuit board of a spa does j1 or j2 matter? I think its a master spa part. S/n 52757***200304110140 Board mas470 master spa le m7.

Ok so after talking to a local pool veteran (45 years in biz). He said there is a water table under the area that can seep through and cause discoloration. He replastered it 12 years ago. He is going to take a look for me. I will post the results...

Black algae or stained plaster? What should I do?

got it ty

Ok so I think easiest way is to take the 2 load wires and connect them to the pump circuit breaker?

its an older system with the newer pda (pda is on/off only no rs45 cable even hooked to vs). I can just make an extra 2 wires to join the 2 hots from motor.

With my Aqualink RS is it ok to wire my VS pump to always have power? My setup only has the pda on/off functionality. I would rather the pump just run the schedule I program.

On a sta-rite heater circa 2007 can you help me? The pressure switch seems to be getting propper voltage but I get a PS error on board. Can a switch with proper voltage still fail?

I have a spa that hasnt been used in five years. I am going to help a friend get it running. Any tips? Also how old do you think it is?

So my air spa switch controller is kaput. What can I replace it with?

So I started a new client on Tuesday. In the process of undoing a union an old cheap check valve snapped. Anyhow over $100 in parts later and 4 hours of labor it was fixed. I asked the client if I could just charge her for parts because it was weak link in the plumbing. She daid no problem. Am I...

I have an older aquarite scg controller. What cells are compatible with it?

I have this valve http://www.amazon.com/Pentair-263028-3-Port-Diverter-Valve/dp/B007VEUGH0/ref=sr_1_1?ie=UTF8&qid=1428131349&sr=8-1&keywords=pentair+263028+o+ring I have a air/water leak at the moment. can someone link me some gasket replacement kits

My inlet difuser on my pump that sits on the inside bottom seems to not fit too snugly. Should it be a glued fit? Kinda snug? My fit does not seem very snug. Anyone have experience on this? My filter has about 8psi when sucking from spa. When I switch to skimmer which is further away I get about...

I need 2 diverter valves 2 to 2.5 variety. What brand is the best w/o breaking the bank? Should I just ebay them? Or can someone post a link a with good deal delivered to California. Thanks

I have been considering a solar kit like the ones sold at Leslie's. I got a quote to have a system installed and I cant afford $4000. I have redone all my rusted pool electrical. Additionally I installed a pentair inteleflow recently. I am looking for feedback on those kits. Also, where can I...