Recent content by Tekcor

Yeah that might be part of a longer term project. My pump can use up to 15.6A of my 20A circuit. That doesn't leave much room for a SWG. So long term, I might have a shed added nearby, get a subpanel there, and run new electrical from that to the pool.

Oh your BJ's has the Austin shock? Mine just has 3 gallon packs of 6 or 7.5%, I can't remember which, for $15. The Ocean State Job Lot has the Austin 12.5%, as well as Diamond Chemical Company 12.5%, both for $19.99. The devil is in the details. Every box of the Diamond had a date of June 8th...

Just got around to checking the date. 22206. So July 24th. We'll call that three weeks. It's been pretty warm, so although I think it's been closer to 80F in the garage, let's call it 90F for the sake of argument. That should be 9.1% according to the chart. Of course, I have no idea what temp it...

Yeah, cost. The way the plumbing was setup, there’s no logical way to fit additional equipment. It’d pretty much need to be done over. So the initial cost of the equipment itself plus the labor to rework the plumbing, means it’s not really viable. Oh and electrical too. I only have a single...

For the past ten years I’ve been using 12.5% bleach for sanitization, but I’ve been mostly in the dark about levels. I know you’ll hate to read it, but I’d balance everything at the start of the season using the local store’s WaterLink SpinTouch tester, then just wing it on chlorine for the rest...

Well fine. Whatever. The pump is as grounded as it could possibly be. Definitely more than the previous pump. You're right though, the pool is not bonded and it never will be. I'm more interested in trying to fix the pump than bring the pool up to code.

Oh and I guess I'll add that inside the basket housing is the only place current is detectable. We tried all four corners of the pool and the skimmer as well. Nothing.

Pool is about 40 years old. The only thing metal that comes in contact with the water is inside the pump. Aside from the lip around the walls that is a good 6 inches from the water level, there's no metal anywhere. Not even a ladder. Thank you. My electrician said a bonding grid wasn't...

Since it's only the pump, there is no bonding grid. There's no other electrical components to connect to. The pump is grounded via the mains, and the electrician did connect the bonding lug on the pump to a grounding rod.

It has to be the pump. There's no other electricity in the area. I have no lights, no nothing else. There's just the outlet for the pool pump - which the electrician fully inspected as well - which the pump is plugged into.

I have a Waterway Defender 140 that was installed by the local pool company about a month ago. At the time, everything seemed ok. Two weekends ago I went to pull the basket from the housing and felt a prick as my finger hit the water. Figuring I had a small cut on that finger that I couldn't...

My apologies, the signature is/was out of date. I've updated it with recent hardware changes. Unfortunately, I don't know what I don't know. There's clumps floating in the water. I don't know if that's all of it, if the floc is still in the water, if there is stuff settled on the bottom, and so...

That's not a bad idea. That seems like it would only help with the bits on the surface. Do I need to worry about it elsewhere? I've not had floc fail before - though I only used it once about 7 years ago - so I'm not really sure what kind of problem I've got myself into. I just know "don't let...

I don't know what an MPV is, but the filter itself (and of course the sand) is about 2-3 years old. It's Hayward stuff. I'm not really looking for help getting the water clear, because the advice is always just "slam it." I just need to figure out what to do about getting the floc out of the...

Everything in the water is dead. My chlorine levels have been sky high, but the filter just can’t clear the water fast enough. It would takes weeks at this rate. So the pool store sold me Bacquacil liquid floc. It’s been 48 hours and just caused some clumping on the surface. How do I get it out...