| Line 34: | Line 34: | ||
JXi heaters are CSA certified for elevations of up to 4,500 feet above sea level. At elevations above 4,500 ft., the heater BTU output can be expected to be reduced by 4% for every 1,000 feet over 4,500 feet above sea level. | JXi heaters are CSA certified for elevations of up to 4,500 feet above sea level. At elevations above 4,500 ft., the heater BTU output can be expected to be reduced by 4% for every 1,000 feet over 4,500 feet above sea level. | ||
| + | ==JXI Head Loss and Flow== | ||
| + | |||
| + | [[File:Jandy JXI Heater Head and Flow.png|thumb]] | ||
==Repairs== | ==Repairs== | ||
Revision as of 15:57, 22 October 2024
Jandy JXI Heaters
Jandy LXI Heaters is the prior model that shares much in common and may also have helpful information.
You will find the model number and serial number on the heater rating plate located on the front of the combustion chamber. Remove the heater front panel to view the combustion chamber.
Jandy JXI models are 200, 260, 330, and 400 BTU heaters for natural gas or propane. Options on the heaters are the VersaFlo automatic bypass or ASME bronze headers with thicker-walled, integral copper fin tubes.
The heaters have a thermal efficiency of 83%-84% and require a minimum flow of 30 GPM and maximum flow of 100 GPM.
JXi with VersaFlo activates the built-in flow bypass valve based on call for heat to avoid running water through the heat exchanger when water does not need to be heated. JXi heaters with VersaFlo factory installed receive a 5-Year standard warranty on the heat exchanger.
Sequence of Operation
- The control system reads the temperature of the water
- Start-up process begins if the temperature is below the set point
- Blower starts, then adequate airflow is confirmed by the air pressure switch
- After airflow is confirmed, the ignition sequence begins
- After a 15-second purge, the igniter gets power
- After approximately 40 seconds of igniter heat up, power is sent to the gas valve
- The gas valve remains open for 5 seconds while the Ignition Control is looking for flame rectification
- As long as flame is sensed at the burner, operation continues until the temperature of the water entering the heater reaches the temperature control setting.
The JXI heater does not have a pilot light. It is equipped with an ignition device which automatically lights the burner. DO NOT try to light the burners by hand.
The blower pushes the air gas mixture into the flame holder inside the sealed combustion chamber.
High Altitude
Appliances are normally derated when installed at high elevation. This is not necessary with the JXi heater because it has a special venturi-type combustion system which self-compensates for changes in barometric pressure. Air flow through the blower inlet pulls the correct flow of gas into the burner regardless of air density.
JXi heaters are CSA certified for elevations of up to 4,500 feet above sea level. At elevations above 4,500 ft., the heater BTU output can be expected to be reduced by 4% for every 1,000 feet over 4,500 feet above sea level.
JXI Head Loss and Flow
Repairs
Workbook JXi Pool&Spa Heater is a training manual for pool repairmen.
BP Electronics or Industrial Electronic Repair has repaired Jandy heater boards. Check with them if your board needs replacement.[1]
JXI Igniters
Silicon Carbide Hot Surface Ignitors are very fragile. That is why they come packed in thick foam packaging. After removing be sure not to bump, scrape or jar the black crystalline part of the ignitor. Also be sure not to touch or contaminate the black crystalline surface with your hands ( it can cause it to fail very similar to a halogen bulb that has been touched with your hands). Although these are not the only reasons for a hot surface ignitor to fail, they are basic precautions that need to be adhered to.
After installing check the resistance of the ignitor with a multimeter. A new ignitor should read approximately 40-90 ohms.[2]
Jandy changed the igniter style a while back as the ones they originally used broke too easily. The old one was like a spiral design.
The new style is more of a solid looking piece.[3]
Flame Rectification Failure
Does the heater briefly ignite and you get a puff of heat and then shuts down? If so you may have have a flame sensing problem. Heater Flame Sensing describes what may be happening and ways to fix it.
JXI High Limit Sensors
A bad Thermal Regulator valve in the water header can cause high limit faults. Check the Thermal Regulator before replacing sensors.
The JXI heaters have two high limit sensors, 135F and 150F, on the bottom rear of one side of the header assembly and the other on the upper front of the other side of the header assembly.[4]
The sensors are simple switches that should be closed when the heater is off. Test the sensor using a multimeter and if it tests open then it needs replacement.
The sensors come as a set of two in a kit. If one fails the manual says to replace both. The 150F is the one with the smaller threads and will only fit that port.
Replacing Leaking Heat Exchanger in Jandy JXI Heater
Jandy JXI400N - Trouble Air describes how a member diagnosed the problems in his Jandy JXI400 heater, discovered the heat exchanger was leaking, and replaced the heat exchanger.
To check if the heat exchanger is leaking remove the ignitor and look into the burner can. If you see any water then you have a leak.
Jandy/Zodiac PC Board Repair
Some members have had good experiences with BP Engineering, Inc. repairing their Jandy boards.
- ↑ https://www.troublefreepool.com/threads/jandy-lt400-temp-control-board-question.204686/post-1814462
- ↑ https://www.troublefreepool.com/threads/jandy-jxi-heater-igniter-issues.238709/
- ↑ https://www.troublefreepool.com/threads/jandy-jxi400-problems.242360/post-2124132
- ↑ https://www.troublefreepool.com/threads/jandy-jxi-400n-heater-high-limit-fault.269417/post-2361128
