Re: Control your Jandy equipment from your PC with a $15 ada
unfortunately I have the same problem. I dont know if our equipment is newer so its a different protocol or what. I am seeing data on the stream, but the company's simulator isn't working nor is jbuehls.
How can I tell what firmware my panel has? I dont have any panels - just a Jandy PDA which says PDA 5.0, JBOX 4.0
I know this is an older thread, but I stumbled upon this info and thought it might be helpful for others. Sorry if this isn't the right place in the thread.
JANDY PPD REVISION CODES*
A Programmable Peripheral Device (PPD) with revision letter C to HH will operate with all PCBs with a 44 pin*
socket.*
A Revision I or II PPD will only operate with a PCB which has a 44 pin socket and is a Revision I PCB.*
A Revision J or newer PPD will only fit into a PCB with a 52 pin socket (second generation of PCB).*
1994-Rev. A = Alpha testing.*
1995-Rev. B = Beta testing.*
1996-Rev. C = First production AquaLink RS.*
1996-Rev. D = Allowed Cleaner JVA socket to be assigned to an auxiliary by turning on dip switch 7.*
1996-Rev. E = Programmed ON times not recognized after freeze protection activates.*
1996-Rev. F = RS 2/6 Sharing a heater support, light dimming on RS 4.*
1997 – Rev. G = First support for SpaLink RS, Cleaner JVA can be assigned without turning on dip 7.*
1997 – Rev. GG = Cancel button locks-up system.*
1997 – Rev. GGG = Correction to GG.*
1998 – Rev. H = First support f or LX / RS 485 connection, memory expansion to 128K of ROM, SpaLink reads*
pool temperature and OFF when the system is not on.*
1998 – Rev. HH = Corrects time calibration problem with Rev. H.*
1998 – Rev. HH 232 = Support for RS 232 Serial Adapter.*
2000 – Rev. I = First support for OneTouch, includes serial adapter support. Note Rev I will only operate in a Rev.*
I PCB.*
2000 – Rev. II = Corrects problem with auxiliaries assigned to f reeze on OneTouch.*
2002 – Rev. J = Change to 52 PIN PPD and new socket on AquaLink RS PCB.*
2002 – Rev. JJ = Corrects problem with auxiliaries assigned to freeze on OneTouch.*
2003 – Rev. K = Support for FlowLink, items manually turned on will reactivate after going to Auto/Service/Time*
Out.*
2004 – Rev. L = Color Light Control, PC Docking, Laminar Light Pulse Control (LPC4), Chiller/Heat Pump*
operation, Run Time (circuits can be set to run manually f or 1 t o 10 minutes or for 10 minutes to 2 hours in 10*
minute increments). Will communicate directly with AquaPure Chlorine Generator only.*
2006 – Rev. M = Support for AquaPalm wireless remote, Change chlorine production from AquaPure. AquaPure*
(revision must be 11230A05 or newer). Assign OneTouch buttons to SpaLink RS buttons.*
2006 – Rev. MM = Corrects problem when entering into lights labels.*
2006 – Rev. MMM = Corrects problem associated with daylight savings which caused the AquaPalm to jump*
lines. Light dimming can be adjusted from AquaPalm.*
CPU REVISION CHANGES*
2007 – Rev. N = Complete change to PCB. The operating chip is no longer a PPD, it is now a CPU (Central*
Processing Unit) board. The AquaLink RS can be connected via the RS 485 line to a Jandy AE Heat Pump &/or a*
Jandy LXi Gas Heater.*
2008 – Rev O = Communication with Variable Speed pumps.*
2009 – Rev P = Communication with ChemLink, LM3, AutoClear Plus & DuoClear.*
2010 - Rev Q = first support for Touch Screen panel.
2012- *Rev R = internet control of Jandy Aqualink system via smartphone or web*