So I recently had my pool redone with Wet Edge (PebbleTec competitor). I've been brushing and balancing the water the past two weeks. My numbers were good but CSI was around –0.52 but I was still working on getting it up.
PH – 7.2
TA – 80
CH – 210
CYA – 30
FC – 3
Water temp – 74
CSI – -0.52
Then this past weekend, the Wet Edge guys came out to further expose some of the pebble aggregates around the steps and bench areas. To do so, they had to pour A LOT of muriatic acid. This dropped my PH to below 6.8 I assume since the test result was very yellow and faint and TA was down to 0. So off to Costco, bought a few bags of baking soda and boxes of borax. First I raised TA back up to 80. Then I dropped in the borax. Well, I know with borax it will affect the TA but it went much higher than I expected.
Here are my current readings:
PH - 7.5
TA - 120
CH - 220
CYA - 30
FC - 3
CC 0.5
Water temp - 74 F
This gives me a CSI of -0.03.
So now I’m conflicted. My CSI is close to 0 but the TA is higher that I originally wanted and I do want to raise CH to 250 (maxed) eventually as that is what’s recommended for Wet Edge. In the Lower Total Alkalinity page (Pool School - Lower Total Alkalinity), the writer wrote that "There are two reasons to lower your total alkalinity (TA) right away, because you want to slow down the rate that the PH rises, or if high TA is contributing to a high calcium saturation index (CSI) which puts you at risk of calcium scaling. You shouldn't lower TA just to reach a target number. Make sure you actually have one of the above issues before lowering your TA.” I don’t see either issue. My question is, are these values ok for the long term? Or should I rework the chemistry to more inline on what’s recommended like this:
PH – 7.5
TA – 80
CH – 250 (maxed)
CYA – 30
Water temp – 74F
CSI - -0.18
Two more questions:
1) For the Taylor test kits, when do you stop counting the drops? So let's that the TA test, it starts out green. The instruction states to take the reading when it turns red (or in my case I see pink almost all the time). However typically it changes from green to something like grey and then an additional drop would change it to pink/red. At what point do I stop counting? At the grey or when it fully turns pink/red?
2) Is there a test kit that gives more finite ph values? The one from Taylor goes from 6.8 -> 7.2 -> 7.5 -> 7.8 -> 8.2. If a ph of 7.4 or 7.6 can make a pretty big difference in the CSI, why not have something more precise? Or all these approximate values are good enough?
PH – 7.2
TA – 80
CH – 210
CYA – 30
FC – 3
Water temp – 74
CSI – -0.52
Then this past weekend, the Wet Edge guys came out to further expose some of the pebble aggregates around the steps and bench areas. To do so, they had to pour A LOT of muriatic acid. This dropped my PH to below 6.8 I assume since the test result was very yellow and faint and TA was down to 0. So off to Costco, bought a few bags of baking soda and boxes of borax. First I raised TA back up to 80. Then I dropped in the borax. Well, I know with borax it will affect the TA but it went much higher than I expected.
Here are my current readings:
PH - 7.5
TA - 120
CH - 220
CYA - 30
FC - 3
CC 0.5
Water temp - 74 F
This gives me a CSI of -0.03.
So now I’m conflicted. My CSI is close to 0 but the TA is higher that I originally wanted and I do want to raise CH to 250 (maxed) eventually as that is what’s recommended for Wet Edge. In the Lower Total Alkalinity page (Pool School - Lower Total Alkalinity), the writer wrote that "There are two reasons to lower your total alkalinity (TA) right away, because you want to slow down the rate that the PH rises, or if high TA is contributing to a high calcium saturation index (CSI) which puts you at risk of calcium scaling. You shouldn't lower TA just to reach a target number. Make sure you actually have one of the above issues before lowering your TA.” I don’t see either issue. My question is, are these values ok for the long term? Or should I rework the chemistry to more inline on what’s recommended like this:
PH – 7.5
TA – 80
CH – 250 (maxed)
CYA – 30
Water temp – 74F
CSI - -0.18
Two more questions:
1) For the Taylor test kits, when do you stop counting the drops? So let's that the TA test, it starts out green. The instruction states to take the reading when it turns red (or in my case I see pink almost all the time). However typically it changes from green to something like grey and then an additional drop would change it to pink/red. At what point do I stop counting? At the grey or when it fully turns pink/red?
2) Is there a test kit that gives more finite ph values? The one from Taylor goes from 6.8 -> 7.2 -> 7.5 -> 7.8 -> 8.2. If a ph of 7.4 or 7.6 can make a pretty big difference in the CSI, why not have something more precise? Or all these approximate values are good enough?