Search results

No luck finding Jacuzzi parts so I opted for a new filter setup. Family Leasure has a eco Kleer 22" with 1.5 motor. The only problem I see so far is that, eco kleer recomends that the filter be placed no more than 5 feet from the pool. My old filter is 23 feet from the skimmer and 21 feet from...

I have a crack at the pressure gauge port and water running down the side of the multi port valve on my filter. I can try finding another multiport or replace the whole filter. Because Jacuzzi 190L parts are getting rare, I'm thinking a new filter is in order. If I can not find a new valve, how...

Well the temps were right this weekend for changing the liner and most all went well. With the new liner, skimmer box and return on hand, I pumped water out removed old liner, repaired floor imperfections. Laid out the new liner and it fit the floor fine. The seams fit the floor/wall corner...

I will be installing a liner in my Esther Williams above ground, beaded 18x33x50 soon. Approximately 30” in ground, on one end and 24” on the other. The liner was ordered last month and it arrived last week. I know that I have some work to do on the pool floor because it has washouts where it...

My water has changed colors and shades of color for the past 3 weeks. Green, dark green, light green, whiteish green, light blue and now I can see the bottom but water is still not clear. It just takes TIME for the filter to do it's job when the water gets out of balance. I keep thinking it's...

One post that blocks pics is "Wierd Colored Water-Seafoam Green", posted by Fancypants in the Testing and Balancing Your Water section. Strange, by the time I typed this reply, the pic of Fancypant's pool appeared. Maybe my computer takes time to load the pics and displays the message untill then.

I'm not sure which posts they were. I have been all over this place reading for several weeks, and now that I ask why, I can't find them. Pretty sure they were in the Pumping Station somewhere. If I see it agian, I'll reply. Thanks for now.

You do not have the required permissions to view the files attached to this post. Why??

FC=21 CC=1 TC=22 PH=7.5 TA=40 will adjust in the next day or two CH= this was orange not yellow CYA=50 Ambient temp about 82 Brushing and vacuume daily Water has cleared enough to see the channels washed out under the liner. :roll: 10 year old liner gets replaced next year. I rinsed out the...

If the hose has been stepped on or kinked, it can and probably will collapse.

Snug the screws down evenly.

I would suggest plugging the lateral stand pipe, maybe wire tie a baggie over it. I don't think sand in the stand pipe is a good thing.

I would guess that there is a formula for finding the turnover rate for a given pool and it's components. But is there a way to measure the actual turnover in my pool?

I was going to hold off on changing anything till the water clears up more. Vacuuming, brushing, backflushing daily and keeping the chlorine about the same was all I was going to do, unless I'm missing something.

Thanks. I'll get the hang of this testing.

Being a new pool owner, and not knowing what was in my filter, I changed the sand last year. It's just that I wanted to know what's inside and that it was correct. Poured in the proper amount of sand and let it go. I only wish I had noted what the full mark was for later reference.

Did the test in order with the instructions. K-1000 CL=orange ph=8.2 Chlorine drop test; 1 scoop R-870 =turned pink R-871 solution cleared at 48 drops x .5=24 FC added 5 drops R-0003 and solution turned pink added 1 drop R-871 to clear up solution 1x.5=.5 CC 24 FC+.5 CC=24.5 TC Total alk...

The pump is about 12 feet from the pool and the 1-1/2" PVC runs undergorund. I know that there is an algae problem, hence the new test kit that just arrived and checking for restrictions. Checking the flow is why I started this thread. I am trying to figure out how to be POSTIVE that there...

CYA reads 60.

Last year the water comming from the eye/return seemed to have more pressure. It almost hurt to put my arm in front of it. I opened the pool about 2 months ago. As for it not clearing up, the water is cloudy after 60 plus days of constant filtering and vacuuming. I have SHOCKed it twice in...

Pressure is normal. I backwash daily and after each vacuum. I have not taken the pump apart, but I can feel the impeller through the strainer and do not feel debris on the impeller. I change the filter sand last year.

I don't seem to have the flow that I had last year and the water just will not clear up. What do you use to check for restrictions? I have 1-1/2" supply and return PVC pipe.

Last year we bought a house with an existing pool and thanks to this site I was able to keep the frogs on the outside. I just ordered the test kit so it should be a little easier this year.

Thanks. I ordered the TF-100.

I put off buying a test kit last year and used the test strips. Having decent results using BBB with the strips, I figure I'll up my results and get a test kit this year. Is the Taylor K-2006 the proper kit for my pool?

New member and testing sig.