Search results

I ran another OCLT last night. TC last night was 5, TC this morning was 4!

Is it possible that I’m losing this amount of chlorine due to the low CYA levels?

The two circles are the drains. There are two LED lights in the pool. One on the wall across from the Baja shelf and another on the wall furthest away from the stairs. I will check the skimmer, skimmer door, and lid. The current level from this morning in full sun at 99 degrees is FC 4, CC...

OCLT result. TC last night was 8. TC this morning was 5.5. I guess I have to slam it some more🙄

All spots are still gone. I began the OCLT tonight. FC 7.5, CC .50, TC 8. Hopefully tomorrow it will be no less than 7.🤞

Not yet. Unfortunately, my schedule won’t allow it until Wed/Thurs.

All spots are gone! This evening’s levels were FC 8, CC .50, TC 8.5. That is 1/2 the amount present yesterday evening. I added all the liquid chlorine I had which was 64oz. Per the TFP Calculator, that should bring it up to 11. The Hayward SWG panel is saying the salt level is low now (2600).🙄

Update. 3 gallons of liquid chlorine was added this morning, pool was swept, pump ran all day. By this evening, all but one spot was already gone! I tested the water again, the FC was 13, CC .50, TC 13.5, CYA still at 30. I added another half gallon of liquid chlorine as the calculator said...

My pool does run off the same water line as the water softener.

Pool store has limited hours today. So there’s a win. After speaking with them on the phone, they are pushing me towards a “rapid” powder chlorine shock and not liquid chlorine. What’s up with that?

I have counted five stains total. Four are on the floor, one is where the floor transitions to the wall. I have tried brushing it away with a nylon brush with no luck.

I was doing what I could with everything being closed on a Sunday night (and potentially today due to Memorial Day). Just so I understand, the chart says my FC needs to be at 16?

Alright, last night I added 3 tabs of chlorine direct to the skimmer basket, then added muratic acid. This morning I cleaned the salt cell and fixed the no flow sensor issue. Here were my levels this morning… FC = 1 CC = .50 TC = 1.50 CH = 250 TA = 120 CYA = 40 CL = 1 BR = 2 PH = 7.5 SALT 2600

I tried brushing with a nylon brush. Nothing happened.

Then it’s 40.

I went out to do my daily visual check on the pool and found a few yellow circles on the pebble sheen. I forgot to check the levels last week and tested them a few minutes ago. I am embarrassed to share these levels… FC .50 CC 0 TC .50 CH 250 TA 140 CYA 35 CL 0 PH 8 SALT 2200 I then checked...

I am still working on this salt water pool. Seems like I can never get the balance perfect.😡 FC: 4.5 CC: .5 TC: 5.0 CH: 275 TA: 100 CYA: 45 CL: 5 Br: 10 PH: 8.2 Salt: 3200ppm

FC: 3 CC: 0.50 TC: 3.5 CH: 275 TA: 90 CYA: 40 CL: 3 PH: 8.2 Salt was added to my new pool this past week. These are my levels. Seems like the PH is always high.

Once the SWG is operational, everyday?

Today’s levels. Kinda irritating... FC: 1.5 CC: 0 TC: 1.5 CH: 275 TA: 100 CYA: 40 CL: 2 PH: 8.2

Alright. Pool Math says to add 3 cups, 6 oz of bleach.

Today’s results after adding -2 quarts, 1 cup, 3 oz of bleach -1 quart, 3 cups 2 oz of muratic acid PH: 7.5 Br: 6 Cl: 3 CYA: 40 TA: 110 FC: 2.0 CC: .50 TC: 2.5 Water Temperature: 76 F Outdoor Temperature: 88 F and Sunny

My pool does refill off of soft water so I am good there. I will look into the pool math logs and I don’t know anything about the signature so I will look into that too!

🙌