Search results

Hard to tell, I replaced wireless and PA, and ran new cable from outdoor antenna to SL panel comms port. Some day I might try to put the old antennas back to see if they work but since everything is working it may be a while before I get around to that.

Shut down for 10, reset PA and router and new system now working. Yay..Im a happy camper !! Still curious about the rj45 connector on the outdoor transceiver ?

Well Im ready for another round of fun with my screenlogic system. Since the previous update here is where I am now. I gave in and ordered a new SL system. Received it last week. I tried install and had no luck. Here is a summary: First I powered down the ET system. I installed new PA and...

well its been over a year but here is that update I promised. I hesitated to replace the gearset because Im not really sure just how well these popup cleaners work. But I do notice some debris on pool bottom so finally found the time to get to this. It was pretty straightforward but I do have to...

thanks. I just got off the call with Pentair. He had me uncover the outdoor transceiver and power light is solid green. (which I have looked at in the past). Since the SL indoor transceiver is currently rapidly flashing they can not offer much help. "It is a comms issue". Pentair says it could...

I was watching the indoor unit yesterday. It would not connect to controller. Then I tried a firmware update on the PA. I then uninstalled and reinstalled the SL app. Still would not connect to controller. This morning it connected right away (when I started the screenlogic app). So I tried...

Also adding the attached

thx. Im not sure how to tell which generation of SL I have. the model number was wireless connection kit 522104. Purchased in 2019. The transceivers(s) do not have a "rabbit ear" antenna . The SL build is 5.2 and rel 738.0. On my mobile app it says version 2.1.0.67. not sure how to find version...

ok, will try that sequence, after the rain :)

you are correct. I had powered off a few times in recent troubleshooting efforts, but I did not power it off last night.

my latest update: I now have a bit less hair :) . On Saturday, SL interface would not connect to the controller at all (windows app). I tried rebooting the router, powering off the indoor transceiver, resetting the PA, and every combination of those actions in various sequences. No matter what...

I powered everything down, then checked the wire connections to the comm port. All seemed good. gave a slight tug on each, no movement. Gave each screw a very slight turn and all were tight. Powered back up. Noticed the VS pump had Err 000f flashing and then it cleared and started up. I guess...

so i just went to SL to see if I could use the guest network, but I am unable to connect to controller again. (I did not change any settings and still on home network (not guest).So I will look at wires tomorrow. thanks all..

sorry i no longer have a old router,. But yes, the Orbi mesh has been active for the entire time the SL has been installed and have not had any issues till now. I'll check the connections tomorrow hoping for a broken/loose connection on the com port. i did move all of the equipment (modem...

from my phone app I can log in to my system either locally or or remotely (I can not log in to the demo server). From Windows I only see an option for local system, and I can log in no problem as well. At times I had issues with the "waiting to connect" but right now there are no connection...

thanks. I guess Im still confused so forgive my question if a silly one; I understand the PA translates and provides data via wireless to the panel. I didnt think the PA would retain the data/state, so if not communicating to the panel, when I start the windows app how does the windows app know...

When I use mobile app I can go to circuits and turn on/off. For example I turn on Pool. It stays "lit" in the App so SL knows I turned it on. Then I see in the Windows app that the Pool circuit is on. The Pool (pump) does not actually turn on but SL believes it is on so SL is not sending the...

Thanks srqpoolguy. btw Im also in SRQ. I appreciate the suggestions. I have tried unplugging, resetting the adapter. powering down router etc. Nothing seemed to fix it. The SL has been working for 4 years. I do have it plugged in to router in my orbi mesh network. It has worked fine till...

thank you James

Oh now i get it :). I could send pics but basically all Im trying to do is hardwire my screenlogic protocol adapter to determine if the comms problems are due to the outdoor transceiver. I have no other equipment issues just the screenlogic interface which had been working for years and...

All of my wiring was done in initial ET install by electrician. I agree the wire colors should have been done per the install documentation. I guess he had some spare wiring he used instead. Since everything had been working for years Im not really looking to change anything. But I wanted to...

i dont have a saltwater pool. Im a little confused not really sure what the attached pics are (I didnt attach them)

Im sorry, not sure what the SWG control power box is?

ahhhh, yes, I have a whisperflo VS pump. Thanks.

My screenlogic stopped communicating to my easytouch system recently. It seems to receive correct information from ET (pool water temp, circuits running etc) but does not communicate changes I make with the App or the Windows interface. For example, i turn on Spa and the button on the windows...

Just to close this out: found the part on Amazon, 158.00, installed it, all is well. Thanks everyone.

Once I posted these pictures I noticed that PN of 178555 at the bottom of the paper label. So I think that is what I need. thanks

My neighbor is out of the country. Im keeping an eye on the home for him. Today I noticed a spray coming from the top of his pentair cartidge filter. It has a small crack in it. I turned off power to the pump for now. Waiting to hear from him on how he wants to proceed. However I thought if I...