Search results

My older Jandy Aquapure SWG setup is now connected to a 3rd party SWG cell and has worked flawlessly since I replaced the Jandy trisensor in May of 2024. Recently, however, It has stopped generating chlorine both standard and boost modes and shows error codes 172 ( Flow sensor service condition...

What will happen if I turn off the pool equipment and throw a submersible pump into my spa to empty into my contiguous pool? Will pool water drain back into the spa on its own? I need to repair the standpipe. Thanks. David - Dallas

Help troubleshooting my Aquapure 1400? For a couple of weeks my Aquapure has failed to generate Chlorine automatically regardless of dialed in % but does generate chlorine well under BOOST. The failure was first noted and attributed to a severe but focal buildup of scale completely obstructing...

I've been running salt water pool through winter with just pool service when I noticed a little green tinge to the water. Tested Chlorine <1. No notice from service but they added 1 bag salt. I added liquid chlorine and then SWCG boost with bubbles seen, but sometime in following week saw a...

Were you able to fix this? Did Helicoil work? thanks, David - Dallas

Help - A diagnostic challenge(with no unifying answer?) History of present illness 1 Jandy Stealth pump (3 years after replacement of dead single speed original motor with 2 speed Century 2–2.5 hp) [edit - actually 1.5->2.2 hp] shows diminished volume, begins to make noise , then quits...

Pool pvc and new filter I am replacing an old Jandy DE filter with a hairline crack with a new Waterway cartridge filter. The Inlet/outlet configurations are inverted with respect to each other so moderate replumbing will be required. It would be much easier to do if I just cut out the old...

My old Jandy filter has a small crack at its inlet junction. I assume unequal stress/torque due to a poor pipe orientation did this over time. 1. Since perfection of orientation is unlikely In my own clumsy filter replacement, would heat softening/bending of the mid sections of the pipe with a...

Two questions 1) Is my SWCG working? My Jandy PLC1400 was giving a PDA error and was clogged with scale. It also shows some corrosion and erosion (see image). I knocked a lot of the corrosion off, and the error notice is now intermittent. I will clean with acid if recommended. Will a...

Moved from HERE Is it reasonable to descale my Jandy PLC1400 with vinegar? I don't have a good storage site for hydrochloric acid.

Several years ago before I retired I hired a pool service of variable quality and quit monitoring my pool chemistry. Yesterday I saw a green tinge to my still too cold to use pool and did a rapid colorimetric chlorine test using my now 5(?) year old K1000 test kit. Result - 0 to 0.5 ppm total...

i have an old Polaris 280 which leaks at the swivel where it connect to the hose. Tightening the nut did not help nor did cutting off an inch or so of hose to provide a "fresh" bit of hose at this connection. 1) Could it be that the hose is so stiff with age that the teeth of the nut threads are...

1) When Jandy phone support, Inyo Pools, and an Aqualink PDA dipswitch setting indicated I could control a 2 speed motor with my current panel, I ordered a new 2 speed motor and pump relay switch (#6796) for my failing Stealth single speed. Before taking my system apart I started to try to...

In partial appreciation for the help I have gotten from this forum, I have 2 circuit bds and 1 LCD from a Jandy LXi400 replaced for a burnt out heater box. The bds still function or did last time I turned them on. If someone with an Lxi would like them contact me, agree to pay postage, and I...

Help. I flipped on my 10 yr old Jandy LXi 400N 2 days ago after not using it for 5-6 most. After there was no change in temp the next day, I checked the unit to find a heat limit error. Examining the unit closer I see the corrosion evident in the attached photos. I also notice no check valve...