Search results

I am using the Taylor K-1766. DSP seems to think I may have a bad temp sensor in the flow switch, a new one is on the way🤞

I wonder what I have done differently? I’ve had the control panel and the cell replaced and my water is 68 degrees. The only way I can get it to start working is by pouring hot, very salty water in the skimmer. A new flow switch should be here tomorrow maybe that will fix it. I’m glad to hear...

You guys are fabulous,.. thank you so very much for all the time you have spent trying to help me. I will talk to DSP about switching the cell around. I installed it according to the picture in my manual. It’s a very tight fit, if I turn it around I won’t be able to pull the cell in or out with...

Same salt I always use. I calculated with pool math app,.. I have added 280lbs since I opened 6 weeks ago. I opened at 2000ppm, 56 degrees. We did have a lot of rain two times with over flow and backwashing.

I spoke with a different guy than I usually speak with, but he was aware of the situation as it appears the whole tech team is trying to figure this out. He asked why I decided to pour hot salty water into my skimmer, so I ratted you out😘 He said he has been there for 16 years and has never...

My flow switch attaches to the control panel. The control panel automatically accepts 110 or 220 without having to change anything. Others have mentioned my flow switch being very close to my pump (I did that in order to fit into my pool shed), I did speak with DSP about it and sent photos and...

Mine does not display salinity😩 I’m using the K-1766 that shows 4200, but I have no way of knowing what the cell is seeing. I don’t understand how it continued to run for 5+ hours last night, obviously the temp and salinity in the cell dropped during that time. I’m supposed to get a new flow...

Another UPDATE So,.. after the very, very salty hot water was poured into the skimmer last night, while the SWG was on, all my lights turned green and it ran for 5 hours then I shut it off. I hooked the timer back up and set it to come in this morning. It again started to generate, but lights...

I did adjust a screw. DPS sent me a detailed set of instructions with photos. I turned it 1/4 turn to the right,.. when that didn’t work I moved it back and then turned it 1/4 to the left. It didn’t work until I poured hot salty water through my skimmer while it was running. It ran for 5 hours...

It’s still running!!😃😃😃

My psi is 10-12. DSP already shipped a new flow switch, that’s the only thing we haven’t tried. It’s still running!

This is the set up

What do I do with this information,.. it was a way concentrated amount of salt, and it was hot water,.. it’s been running for about 30 minutes now. Why? And,.. I love you

OMG!! I picked up my salt from Lowe’s, did as instructed,.. now explain this to me!!

And I’m out of salt😩 I’ve order some from Lowe’s, so I’ll try when I get it. I switched plug ins,. No change😢

No,.. the cell light and salt light never turn green. They go from off to red.

If by duty cycle you mean the % of chlorine output, I’ve tried it at all of the settings. Same results, it works for about one minute, the flow light stays green, the generator light goes off, the cell light turns red and the salt light turns red. The water temp light never comes on, water is...

so,.. the hose didn’t help. I have adjusted the salinity sensor screw both left and right,. Still not working. I’m running out of ideas.

Update: help me please😩 I received my new cell yesterday. I installed it this morning and still have the same results. The green flow light comes on, then the green generator light comes on, I can see it producing the chlorine gas. It runs for less than a minute, then the green generator light...

DPS has shipped a new cell today. They think it is a faulty sensor in the cell.