Recent content by pncsmith

  1. P

    Through Wall Skimmer for Intex Ultra Frame

    Silicone did the trick, no more leak! Happily skimming now!
  2. P

    Through Wall Skimmer for Intex Ultra Frame

    Thanks LFrankow, I will give it a try and report back on the results.
  3. P

    Through Wall Skimmer for Intex Ultra Frame

    I have a combination of one of the bottom drains converted to a return along with the skimmer and pump discharge routed to two of the factory holes in the sidewall. Cutting them out and converting the fittings can be found here: Useful Links for Fellow Intex Pool Owners ,hope this helps.
  4. P

    Through Wall Skimmer for Intex Ultra Frame

    Yesterday I installed a Wide Mouth skimmer on my new Intex 16 X 32 Ultra Frame and made the mistake of centering the skimmer over a vertical seam. Realized what I had done as I was cutting out the skimmer opening. I brought the pool water level up and sure enough the skimmer is leaking. Now...
  5. P

    Intex 16x32 New Install - Pavers & Dimensions questions

    My thread from a few years ago may help........https://www.troublefreepool.com/threads/new-install-intex-ultra-frame-32-x-16-x-52-ag-pool.77778/#post-667187
  6. P

    Hayward SP1091WM with intex pool

    I installed the wide mouth in our 16' x 32' Intex and it works great. Trouble Free Pool
  7. P

    Foam Bottom questions

    Used the 3/4" extruded foam sheets from Lowes around $15/sheet. For 16'x32' pool I needed 16 sheets. Worth the price!
  8. P

    Time for a through-the-wall skimmer

    I second what POPPA S said in that you won't regret installing the skimmer. I have had several AG pools and this is my first with the skimmer installed which does a great job at clearing debris. I also use a solar cover frequently and the skimming is reduced but once the cover is rolled up the...
  9. P

    Elephant pad under new pool install?

    I installed the Gorilla Pad over foam board underlayment, worked very well. http://www.troublefreepool.com/threads/77778-New-Install-Intex-Ultra-Frame-32-x-16-x-52-quot-AG-Pool
  10. P

    The new pool arrives tomorrow

    Information from my install that may help... http://www.troublefreepool.com/threads/77778-New-Install-Intex-Ultra-Frame-32-x-16-x-52-quot-AG-Pool
  11. P

    New Install - Intex Ultra Frame 32' x 16' x 52" AG Pool

    Correct, using a 32' x 16' layout. Just keep in mind that the braces are 20" wide and you will need to determine where the center of your pad will be. If you are using a 16" pad as I did you would need to start the edge of the first board on the long side at 29" and the short side at 25".
  12. P

    New Install - Intex Ultra Frame 32' x 16' x 52" AG Pool

    From the corner to the edge of the first brace on the long side is 27", 45" between the braces measured at the centerline. From the corner to the edge of the first brace on the short side is 23", 42" between the braces measured at the centerline The support braces are 20" wide outside edge to...
  13. P

    New Install - Intex Ultra Frame 32' x 16' x 52" AG Pool

    Additional dimensions that may help with the layout preparing for installation... The insulation base is 32' x 16'. The support legs around the pool extend 7" out from the insulation pad. The centerline distance between the long side supports is 45" The centerline distance between the short...
  14. P

    Intex Ultra Frame Pool 32 x 16 x 52

    Info from my install that may help. http://www.troublefreepool.com/threads/77778-New-Install-Intex-Ultra-Frame-32-x-16-x-52-quot-AG-Pool
  15. P

    how to connect 1.5" Backwash hose and Intex 2800gph Sand filter

    I used 1.5" barb fitting and the modified adapter found on this site for the Intex pool connections