Search results

They have one called an "Encore". It looks like and Active 20 for half the price...

It appears Maytronics signed an exclusive privilege deal with a company in Canada called Pool Supplies Canada. I have been trying to find a S300 up here and no one carries them. My guess is this Premium is the S300. Can anyone help to confirm this. Thanks in advance

It’s a T-15

Rechecked numbers are 2300 78 30.6 3.06 99p -1600 al-1 r-1.40 Now getting solid check salt and solid inspect cell

Pump is usually running on low speed. No issues with no flow.

The cell is 10 years old. I have a timer on pump and and a separate timer on aqua rite. The aqua rite turns on an hour after pump and shuts down an hour before pump turns off. With the unit on auto. Here is what I get when I push diagnostics 2300 78 30.3 0.00 99P -0 AL-1 r-1.40

I have recalibrated my cell at least 4 times. I set it and the next day it continually drops so low that it shuts off and the lights are blinking. I used test strips and they state 3000 ppm and I had the water tested and it showed 3100 ppm. Any ideas as to what is going on.

My backwash is a solid line to my ditch underground so I would never notice a leak.

I do have a suction, went and put lube on all the gaskets. Have not run pump since doing so. I thought the hissing sound was a result of a bad spider gasket letting air back in through the backwash.

Folks, I need some guidance. When my pump shuts off I hear a hissing sound in the multiport valve and water draining . My gut instinct is the spider gasket is done. The filter is a hayward S244t, the multipost valve is an SP0714TC and the spider gasket key/seal is SP0714C. The key seal has...

That is great information. When I removed the multiport valve, and opened the drain on the sand filter, the water would not drain out. I had to suck the water out with shop vac. Once the excess water was removed, the unit was a little over half filled with sand. I removed the sand from the...

I kept getting a low flow light on my SWG, took it off and cleaned it. The low flow stayed on, decided that i needed to change the sand in the filter (it's been 7 years) found a broken lateral and fixed that. Now the low flow sensor is off. Went to vacuum the pool and did not have enough suction...

Does anyone recommend a distributor in Canada, specifically in eastern Ontario. I will go outside Ontario if shipping costs are not bad.I would like to purchase this heater at a reasonable price. Thanks

Great info. Next set of questions. Copper or Nickel input? Where is the best place to purchase for a good price?

Folks I need your guidance. I'm going to purchase a natural gas heater for my inground pool. It is an 18X36 with no deep end. It holds about 90,000 liters or 24000 US gallons. It seams that Raypak is the most recommended on the site. I noticed they carry two types a Low Nox and their regular...

Here is my situation. My pump room is approximately 90 feet away from the meter and is attached to my garage. I have an existing underground 1 inch gas line that is connected to my furnace in the garage. I'm in Canada and want to extend my pool season as much as possible. I have an 18 by 36...

I want to istall a Raypak 336 natural gas heater. I checked the sizing and it exactly what I need for my inground pool. My problem if I do have one is that I currently have natural gas running into my garage that I use to heat it in the winter. My pump room is a room just off the garage. The...

I just just had an 18 X 36 IG installed about a week ago. It has a hayward 1 1/2 pump and 300 lbs sand filter. After I backwash and rinse, I get this large dust cloud out of the returns for 30 or 40 seconds. The pool looks so nice cleaned but I hate to backwash because it appears to put more...