Search results

Have a 15x30 AGP. Had robot run 4 times. Does a good job within the straight edges of the pool, but almost non existant around the ovel areas. Tried starting it all over the pool, but same result! Sucks (no pun intended) to spend $700 and for it to work this poorly. It searching around, but...

I have to replace mine and hadn't really thought about how to get rid of it? of if it was sand for that matter. I'd prefer not to start a pile of sand in the back yard! thx

The liner is about 3 years old. Small slot about 1/2 in. Leak send VERY SLOW. only reason I even know about it is that one of my kids noticed it when swimming under water. What is the best way to patch it up. Haven't had anything like this and am pretty new to Pools in general. Thx

I have a metal pool sidedeck that needs to have the carpet replaced. It's about 5x15 on an oval above ground pool deck, which is on the long side of the pool. Not sure of I should go with carpet or another material. I live in Western MA. What do you good recommend? Materials, cost, pros and...

Hi, just opened up my pool and realize that the pool timer was not turning the filter on and off. It visually looks fine, the trippers go to the switch but never actually TripIt. I can turn the electricity on and off manually without an issue. The gears behind the dial look fine. The timer wheel...

So I opened up my pool and the side deck, which is carpeted gray, has some staining on it. What's the best way to clean this? Recommended products? I'm assuming a limited amount of products would b ok to use since you gotta be careful with getting whatever you use getting in the pool. Thx

What I can think of, is that I lubricated where the o ring meets the valve, but not where the valve sits on the filter. Could that of been my mistake? It's on both sides where the clamp is tightened by the screw Thx Sent from my iPhone using Tapatalk

See white haze coming into the pool after putting in the skimmer. Just wondering if this is normal. Thx S180t hayward sand filter for agp Sent from my iPhone using Tapatalk

I have an above 15x30 oval above ground pool 52 in deep. 2 speed 2 hp pump. Sent from my iPhone using Tapatalk

Have a 15 x 30 above ground pool to horsepower two speed water pump and sand filter. Hadn't noticed it before because I thought it was the timer going off during the time I get home from work. Yesterday I noticed that after about three hours of the pumping on, the pump continues to run but the...

The bottom seems to be spinning fine. Here's a pic of the pool and the parts it missed. This is after 24hrs and me moving it close to skimmer once Any ideas of why this is happening? Thx Sent from my iPhone using Tapatalk

Also, is the size of a pipe measure by inside or outside diameter? Sent from my iPhone using Tapatalk

As above, the pool is 15x30 oval. Have border and landscape fabric for 3ft wide and 3in deep stone. How many yards would I need? The stone still be 1.5 in river jack. Thanks in advance! Sent from my iPhone using Tapatalk

15x30x52 ago with side deck. Looking to put this the perimeter of the pool add well as under the deck. Using landscape edging, then landscape fabric, then the stone. Deciding between the 2 and since we know nothing about this, figure I'd ask before deciding in case there were advantages of one...

Probably a stupid question, but I'm new to all this. The ladder that came with the pool got knocked down by a wind storm and broke. Now, is there a name for these types of ladders? Is the difference between posts standard? Sent from my iPhone using Tapatalk

hi. We have a 30x15 above ground pool. we were planning on putting down some landscaping fabric around the perimeter. , then about 2-3in of river jack. what size river rock do you guys recommend? thanks.

This is for an A.G.P. pool reel Model is 5000. I called Swimline and they were extremely rude. I was actually taken aback by the poor customer service. I barely started speaking when she asked me if this was a warranty matter, when I said no, I just had a question on installation and how to...

I'm new to pools. Have an agp. All fittings and connections are 1.5 in. Need to add a water bonder. Problem is that it acts like a reducer. Threaded end is for 1.5 in, other end is for 1.25 in( through measuring and experimenting) What the best and /or easiest way to make this...

does'nt necessarily bother me functionally, but worried that the banginig of the bottom of the stairs on the liner will eventually damage it. thoughts?

guessing its the o-ring? flange? both? if and when I get this figured out, whats the best sourse on how to get the filter system properly started again? (ie properly primed so I dont screw it up another way) thanks

This is for an above ground pool. The model number is SD-20-2?11vd. I googled proline, but I dont seem to get a hit on a manufacturer! thanks.

having an existing deck that would like to abut an above ground pool to, but now sure if I can do that. thanks

I know, I know, this is not new, but I keep getting conflicting information. Live in Western MA. Planning on getting a 15 x 24 x 52-54 inches. if not, then 12 x 24ft. (by the way, that's the wall height, what is the actually height of the water?) this is my understanding from the research...