Search results

I have a pool motor that turns on but then turns off and trips the breaker. I replaced the capacitor but this did not fix the issue. I also reached inside and was able to freely spin the impeller. So is there anything else I can do to fix it or is the motor need replacement? Thanks for any help!

I am aware that high CSI results in scaling on the plates inside the SWG cell. This requires more frequent acid washing of the cell. Acid washing, I believe, starts to eat away the cell platings which eventually cause the cell to fail. Is the more frequent acid washings the ultimate cause of...

I need to cut a section of PVC pipe off due to a leak and redo the plumbing with new couplings and pipe. However I need to attach a PVC coupling to a pipe that is faded. Is this an issue? Also for PVC Schedule 40 pipe, I am using the following: Oatey Purple Primer Oatey Medium Clear PVC Cement...

I have the LaMotte 7022 Test Kit. I am running out of the DPD Powder #1 used for the FAS-DPD Chlorine Test. I am having trouble finding replacement powder from LaMotte. However it appears that Taylor makes a FAS-DPD test using a powder called R-0870. Can I used Taylor R-0870 as a replacement...

I live in Phoenix and my filter, pumps and plumbing are all exposed. I'd like to put up some kind of cheap shelter over it. What kinds of shelter do people recommend? Thanks in advance!

My fill water pH=7.4 TA=130. That TA seems a bit high, especially if I want to add boric acid. I could add MA & aerate for a few weeks but I wonder if its just a losing battle since fill water is itself 130. Thanks for any insight.

Here are my readings: FC: 6 CC: 0 pH: 7.4 TA: 130 (Note that my fill water has the same pH and TA) CYA: ~70 Should I consider adding Boric Acid to my pool? If so, is 50 lbs a good amount? People report good benefits but need fairly low TA to add borates. But my TA will pretty much always be...

I have a programmable VS pump running the filter that is permanently powered. It is running 24/7. This is the VS Pump schedule: 0800 - 2200: 1200 rpm 2200 - 0200: 2900 rpm 0200 - 0800: 1500 rpm The SWCG is controlled by Jandy RS8 automation. But currently, I am running it 24/7. (Peak utility...

I have a test kit which measures CYA level using turbidity test. I find it hard to get a precise reading. Determining when the black dot disappears is subjective. Is the turbidity test really better than using CYA strips? Is there some better third way to measure CYA that I don't know about...

I found the following salts for $5.76/40 lbs. http://www.homedepot.com/p/Diamond-Crystal-Solar-Naturals-Water-Softener-Salt-Crystals-100012454/100172669 http://www.homedepot.com/p/Diamond-Crystal-Bright-and-Soft-Water-Softener-Salt-Pellets-100012420/100614653 Can I use either brand of salt...

I am wanting to drain, wash and refill my 20k pebbletec play pool. But temps are already maxing out at 108F on some days now here in Phoenix. Is this something that I should do now or is it too hot even for pebbletec (I believe it is too hot for plaster already)?

I have a Pentair CCP520 Filter and am having trouble removing the drain plug on the bottom. A couple of questions: 1. It has a plastic hex head. What is the best tool and way to unscrew it? I tried using an adjustable wrench and it keeps slipping and starting to damage the hex head. 2. What...

I am in need of replacing my Pentair Amerlite 400W incandescent bulb. I wish to replace it with an LED bulb, maybe even one of the fancy multi-color bulbs. My manual states I need: 1. Pentair American Products O-Ring, Amerlite, Light Lens, O-170 #79101600 2. Pentair 79102200 400-Watt...

I have some debris that is stuck on the pool bottom (leftover sand, leaves, etc.). What is the best way to remove it? I tried netting it but it isn't able to "catch" the debris very well. One thing I considered was buying a second pole and using a brush to push it into the net. This might be...

I have decided to take the plunge and buy/install a SWG for the upcoming season. After much research here and elsewhere, I am leaning towards either the Circupool RJ60 or RJ60+. RJ60: 3.1lbs CL/day, rated lifetime of 11500 hours, 5 year limited warranty for $999. RJ60+: 3.1lbs CL/day, rated...

I have a very new pool pump motor that won't start. It makes no sound when I turn it on. I tried resetting the breaker several times to no avail. I checked the wiring connection to the back of the motor and the ends are screwed in tight and connected properly. I believe it is an electrical...

I am wondering if my impeller is reusable. It has some scratches on it but is otherwise intact.

I am trying to remove the WhisperFlo Seal Plate from the old motor (to be replaced by a new motor). It is held by four hex bolts. I easily removed three of them but the fourth one is stuck. Any advice on how to remove it? I tried spaying it with WD-40 but did not work. Also I am thinking of...

I am in the process of installing a new shaft seal for a replacement motor. However, I read that you need to keep it clean otherwise it will fail. There are two parts, the spring part that goes into the seal plate and another part that goes into the impeller. Which parts of the shaft seal needs...

I am trying to replace the motor for a Spa Jet WhisperFlo Pump. The current motor is Century Part 7-177452-03. Is this a 2HP 1.3SF Full rated motor like this one? U.S. Motors Emerson EB843 Emerson 56Y Square Flange Single Speed 2HP Full Rated Pool and Spa Motor Cost is $300. I also found a...

I am planning to replace my pump motor. When I do, I would like to thoroughly clean my diffuser and impeller and put in a new pump seal. Is there any recommended way to clean them? I was thinking just soap and water with a cotton cloth.

I accidentally cracked the 90deg nylon electrical connector that is directly connected to the side of the pool pump motor. But I am not sure how to replace it. Firstly, am I right that it is a 1/2" connector to the pool pump motor? Secondly, how do I remove the connector itself? The elbow...

I know that if your CYA is high, then you need to keep your FC high. On the chart, it says that: CYA=100ppm Minimum FC=8 Target FC=11-13 Shock FC=39 Is it that at CYA=100ppm, it is just not possible to reach those FC targets? I mean if I bought enough bleach wouldn't I be able to reach those FC...

I have been looking at possibly getting a SWG for my pool. During my research I came across this one: Solaxx Soltran Reliant CLG240A It is rated for up to 40G, 1.65lb Cl/24hrs and currently costs only $550. Replacement cell is $329. It seems like this system is a much better value than...

I am looking to get a second set of cartridges for my Pentair CCP520 cartridge filter. I was considering the Pleatco-PCC130-PAK4-Replacement-Cartridge-Cartridges Although highly rated, their cost is high at $191.02. Then I found Excel-Filters-XLS-706-Cartridge-replacement for only $150...

I have a WhisperFlo pump with a motor that needs replacing. Has anyone done this themselves? How difficult is it to do? I have skimmed some videos and it seems not straightforward as it involves dealing with many parts.

For anyone who uses a cartridge cleaning tool, which one do you recommend? For now, I have narrowed it down to the following: Mi-Way Aquacomb Filter Flosser There may be others I haven't considered as well. Thanks for any insight.

I have a Paramount PCC2000 infloor pool cleaner. Recently the motor died (nothing happens when it is turned on). This is the motor that was being used: Replacement Motor matching AO SMITH Number K48L2PA101A1 Should I just replace it with this exact same motor? Or are there other options I can...

I have a sand filter that is leaking and not cost effective to repair. So I need to replace it. However, it is very low maintenance. All I have needed to do is: Backwash every few weeks (takes like 10 minutes each time) Replace sand every few years (only done once, had to hire someone to do it...

I own a Pentair Triton II filter that is probably around 10 years old or so. One of the two ports is leaking. This indicates the leak is inside the bulkheads and to repair it properly requires an expensive repair (removing all the sand, replacing the bulkheads, replacing all the sand, etc.) I...