Search results

Thanks ajw22. Everything is working fine. The easytouch thinks it’s a gas heater, but that’s fine.

You are a nan of few words. Thank you.

Thanks ajw22. I saw that manual before, but it seems ambiguous. I'm not sure what the NO switch is, and whether it just requires a closed circuit, or is it a relay that requires a current to operate. I also got an installation manual with the unit, which is more detail. I found it online...

My old Hayward HP21104T heat pump died and I replaced it with a W3HP21404T. I controlled the HP21104T with my Pentair easytouch 8 by connecting the easytouch’s heater/fireman’s switch 24 VAC wires to the HP21104T’s remote heat terminals. I would like to do the same with the W3HP21404T. What...

Edited for politeness, jblizzle - - - Updated - - - Yes, I saw similar discussion concerning what I thought were residential pools, which is why I felt my original question was relevant to that topic.

Hi Jason, I'm sorry I may have violated the rules. I've found this forum to be quite helpful, and had no intention of causing problems. I though it was a related question, and thus appropriate. Again, I apologize. However, I must say your response was quite aggressive to an unintended...

This thread had been quite for a while, but it looks like the right place to ask my question. No, it wasn't. Please ask questions in your own topic, rather than hijacking someone else's existing topic. JasonLion I have an EasyTouch, IC40 and IntelliFlo VF. I'm looking at the IntelliChem. I...

Ok. I got it. Thanks.

I'm not sure what you mean by setting the the flow on the heater. I have a Hayward HeatPro, so there is no data cable between the heater and the EasyTouch, just a relay cable to switch the heater on. And there doesn't appear to be a flow setting in the EasyTouch heater menu. As for setting...

This might sound simple, but check the skimmer. Mine sometimes gets stuck in the up position, letting in air, and decreasing presume.

Help setting up EasyTouch to increase IntelliFlo VF pump when heat pump runs I installed an EasyTouch to control my pool equipment. 32k pond shaped vinyl pool IntelliFlo VF pumps IntelliChlor IC40 Hayward HeatPro 21104T heat hump Waterfall EasyTouch 8SP Autelis EasyTouch controller...

I hate ipad auto-correct. The min/max for the Heat Pro is 30/75. The nominal rate is 47 gpm.

Thanks for the quick response. I find this forum to be very responsive, friendly and informative. I don't plan on running the waterfall continuously. Just when entertaining. I forgot to mention that I live in the Massachusetts, and tend to keep a solar cover on the pool when not in use. I...

Just replaced an old SuperFlo 1.5 hp with an IntelliFlo VF. I'm getting an EasyTouch soon to go with it, but for now, I need to know how to setup it up independently. I have a 32,000 gallon pond shapes pool with a IC40, Hayward HeatPro HP21404T heat pump, a pentair clear and clean cartridge...

Thanks for the explanation.

Thank's for the feedback. I take a closer look at the EZT8 and IntelliTouch again.

I'm replacing my current SuperFlo single speed pump with an IntelliFlo VF pump (got a good deal, so I'm going with the VF instead of the VS). Most of my other equipment is already Pentair, except my Hayward heat pump. I'm considering connecting everything with automation, and am considering an...

Hi, I'm new here. I've been perusing the forum, and am finally ready to post my first question. I've had a pool for almost 4 years. 24x40 pond shaped vinyl in-ground pool. 8ft deep. Approx 30,000 gal Pentair 1.5 hp SuperFlo single speed pump Pentair IntelliChlor IC40 chlorine generator...