Search results

I am having an issue with egg timers for my pool and hot tub. I am using the screen logic connect app on my phone and the arrows on either side of the pool and hot tub egg timers is no present. Anyone got a clue what might have happened? Also, if I use the screen logic app on laptop I am unable...

I am pretty sure I had the exact same issue as your wheels but only on one side. I fixed it by cutting the top of a medicine bottle off and sticking it in between the cap that you glued on and the wheel. There is a real thin piece of plastic that is supposed to extend up from the inside of the...

Well. I still haven’t found a replacement. Randomly purchased an R20 bulb at Home Depot today. The bulb was too long.

Ah. Na. It is completely clean inside.

Actually I believe it is an R20 not a PAR20. Like a lava lamp bulb.

Like a standard light socket.

I think it is a PAR20.

It is part of my pool.

I have a blown bulb in my spa and having a heck of a time finding a replacement. It is an American Products 100w 120v fixture. What is the designator for this bulb like a PAR or R number? Thanks in advance.

Annnnd.....After a little more reading I have decided not to upgrade it. There are no clear directions anywhere to tell you what you have to do to make it work. Lots of talk about having to run new wires and replacing the indoor control panel. That is another $350 and I ain’t ready to figure out...

finally got a chance to go look at that upgrade. I had looked at these before. It does not list the Lx3400 as comparable. However, I just noticed the Lx3400 is the controller for the Cp3400 which is compatible. I will probably be ordering one of them now. Hopefully it is a straight forward swap.

I have done this test. They are fine.

I have an LX3400 power center and the temps are way off. My external temp is reading 135 degrees and my water temp is reading 95. I have attempted to calibrate but they will not go any lower than that. I have cleaned the circuit board a few time with 90% alcohol and that typically fixes the...

I wouldn't mind getting rid of the trees but they are a God send when it is 103 degrees outside. I am going to build some leaf guards because when the leaves are bad it is hard to keep them out of the pump cause they get sucked in before I can get the basket back in.

Yea, I really wish that would help. However, the problem isn't at the skimmer it is having a two inch think layer of leaves at the bottom of the pool and having to manually remove them every single day and sometime twice a day. I don't have the time for that. The only way to remotely fix the...

Good. I actually cleaned and recharged them on Sunday (We had 20 degree temps last night and more tonight). I will let it roll through the winter until it gets clogged again. If all the leaves don't fall by then I will just take the grids out. If the leaves are done I will recharge and slam the...

Side valve. I was just off googling MPV valve and I certainly don't have one.

No I do not.

So it takes all winter here for the leaves to fall of the trees and we get rain off and on. I have lots of trees around my pull and it stays green and full of leaves most of the winter. This requires massive amounts of attention and time that I do not have in the winter. I typically have to...

Circuit board was just dirty. Cleaned it with canned air and the error cleared. Both sensors calibrated correctly after that.

Well now they are both messed up. I went out to the power center to swap the air and water temperature to see if the problem moved from one to the other. I could not even get the set screws out of the board. Now I get Err1 on the control center and the air temperature calibration won't go lower...

Woke up this morning and the pool was running because the FRZ indicator was on. It was 55 degrees outside. I looked at the manual for the pool controls and saw I could adjust the pool and air temperatures so i did. However, the control panel will not let me set the water temperature below 88...

Yup, the water was cloudy a couple of days ago but I had it pretty clear when I cleaned the filter on yesterday. Today the water is crystal clear without slamming it. When I said I wanted to prevent a algae bloom I was referring to the entire pool turning green and the entire surface of the pool...

Not sure there is a line from the pool cleaner to the pump. I assumed the line, since it is a pressure side cleaner/vacuum, would run from the pump to the filter to the booster pump and on to the vacuum. My thought was that if there is an obstruction between the filter and the cleaner then when...