Search results

Once the fc comes down, I’ll drop the ph & aerate, see if I can get it down some. My last pool hovered around 140.

Retested - 260.

Test kit is brand new TF100

No auto fill. Tap water here is 7.5, TA-250, ch-75

Yes, held at 32.5 overnight & .5cc. Should I work to drop TA?

Hello, I was introduced to TFP about 5 yrs ago, after fighting chemicals & bad advice from the pool company (never heard that story have you!?). I just bought a new house with an old neglected pool last fall, after selling my house (pool was newer & water was great, don’t ask me why....)...

Circuit board replaced, system functioning properly. Thanks again Ping!

Ping, Here are my numbers today after dumping ~25% & refilling. FC - 3.5 PH - 7.6 TA - 170 CH - 310 CYA - 55 Salt - 3200 :p BOR - 30 The sensor is running program A, Firmware 02 11 0A 10. I don't have the small flow adapter card for the sensor (the previous cell/sensor & cord I took out...

Hey Ping, Im still getting the 123 error code and do not get a reading at the board where the swg plugs in. I received my salt water test kit today and here are my numbers: FC - 9 PH - 7.7 TA - 140 CH - 310 CYA - 60 Salt - 4600 Bor - 30 Temp - 89 Would you suggest: replacing about 25% of...

Thanks Ping, I should have my new test kit on Monday and will verify & set the salinity. The 123 code is the only one that flashes. I did briefly get the 145 as I mentioned, but that is the only time I have seen it. The cell came with a new cord and new sensor. The cell/cord & sensor are all...

Hello, I have Janday Aquapure 1400. I replaced the salt cell (& cord) about a week ago, which I thought was bad. I am now getting an error code "123". I have done the main circuit board tests (https://premium.zodiacpoolsystems.com/~/media/5e517452be9c402b9aef35ce3d54eb51.pdf) and receive...

Hey Ping, I have the 1400 model. I checked the pins and also tested the board where the green & blk/wht wires connect (cord from the cell) and only get 0.0. All other board tests pass. I did just receive a 145 error code (reading the salt at 5300, I normally keep the salt at 3200-3400 and...

Thanks Ping, I haven't seen any other codes that flash other than 123. The cell/cord/sensor is only about a week old. I will double check to make sure the pins are tight. I don't believe I am getting any voltage to the cell though.

Hey guys, I also have a Aquapure 1400, and am receiving the 123 error code. I recently replaced the cell/cord/sensor because I thought the cell was going bad (about 3yrs. old). I don't think I am getting any reading at all with my multimeter at the cell? Does this mean the circuit board...

Thanks, Smykowski. Would you recommend a partial drain/refill to lower the calcium level?

Thanks Woody. Think the calcium is high enough to partial drain/refill, or am I being too picky? ...Your right pwrstrk..I didn't say it, but another posted that my cya could have been "backwashed out" a little since I put the cya through the skimmer. Is this not correct since I have a...

Im not following? "backwashed out"? Meaning it's caught in my cartridge filter?

Great! I posted my tap water results also (was curious about them too, and with a new test kit....) Anyway, do I need to worry about my TA & CH being high? Im a little nervous about scaling with my swg. Or any reason to partial drain/refill? I did notice my TA starting to very slowly drop...

Fairly new to TFP, and have been trying to follow the help you all have given me! Here are my latest readings, as well as my tap water readings. Pool: FC=6 CC=.5 TA=150 CH=410 PH=7.4 Borates=50 CYA=Less than 20 Tap Water: TA=250 PH=7.5 CH=80 on 6/23 my pool store told me my cya was about 35...

Thanks Again!!! Have a good 4th!!

YOU GUYS RULE!!! I appreciate the help, I'm sure I'll have more questions as I become more familiar with TFP!

Another dumb question.....Since I have people coming over on the 4th to swim, will it be safe for them if I need to continue past tomorrow?

My temp is 90, and the water is crystal clear and sparkling.

Awesome, thanks guys, dropping my ph now, then shocking up to 16ppm FC!!! How many hours would a ball park be to keep the FC at 16? (I know I need to test my CC to make sure its at .5 or below, and also the overnight FC loss test) just curious on if I should start up with the bleach tonight?

I also just looked at the shocking process and see that the CYA for swg starts at 60, do I need to raise my CYA to 60 before shocking? If not, and I can raise it after, what are the target numbers?

I will test my tap water, is there any worry about scaling, (obviously a little freaked out about scaling up another swg)?

After getting "pool stored" for a couple of years, and now finding this site, my TF-100 arrived today. Here are my numbers. To start with, I was thinking of draining about 25% of my water, due to the high CH/TA, then adjusting what I need tomorrow as far as PH/FC/Borate/(possible CYA if I need...

They told me my cya level was 37. Aquajunk test strip says between 0-30. I added two huge 3-5gallon buckets of supreme last summer. Probably added 8-12 inches of water since.