Search results

Here’s a better picture of the plumbing. Pipe extender is pretty cool. Do I cut off the pipe right below the Tee and above the existing union and then suck it inside the pipe that’s glued into in?Will it hurt the flow?

Im back. I got my new Pentair Intelliflo pump today. The old Sta-Rote pump had the male threads that the union connects to. The new pump requires a new union half to screw into the pump. There is a part number on the union nuts U11-200PS. Is there a union half that will connect to this or do I...

I checked that and it’s it 241v.

Sounds like a good idea. I’ll get one.

Awesome. Thank you again for your help.

Sorry. Don’t why I typed that model number. I meant to ask if the 011056 will work with my Easy Touch.

Will the 011018 work with my Easy Touch? I don’t have anything fancy but I do like the controls. Appreciate all the help.

It’s 8 years old. I’m fine with buying a new one if it’s dead. Just wanted to see if I was missing anything. I see Amazon has the Pentair 011056 for $1,400. Looks to be the cheapest I can get a new one for. Is this model any good?

Ok I did that and it’s still a blank orange screen and doesn’t run.

That’s correct. No SWG or Screenlogic. I put it in service mode and the screen is still blank. Just the orange backlight.

I turned the breakers off for a few minutes and it didn’t change anything. I have a Pentair heater and air blower for the spa connected to the same controller. They both seem to work. I turned off the gas to the heater and told the system to heat the pool and it powered up.

I was out of town for a week and just got back. My pump isn’t running. It’s a Sta-Rite Intellipro variable speed. The display is blank but the orange back light works. It’s connected to an easy touch system. Any suggestions where to start for troubleshooting? My daughter said while we were...

Thank you. I’ll be sure to buy one of those kits.

Here is a picture of the plumbing at the heater.

I think so. There pipe from the pump is long and has enough play in it. The outlet side might be harder. I was thinking about using 3 90’s to make a u in the pipe so I can offset it.

Looks like they are about an inch higher so that should work.

I have a Sta-Rite max e therm heater. Rats made a nest for who knows how long their pee rusted out the top of the combustion chamber. I was thinking about buying a Pentair heater to replace it. I read they are the same internals. Will the water and gas connections line up on the Pentair or will...

I took it apart again and found a small hairline crack in the pump housing under the clamp. I just ordered a new one. Thanks for the replies.

I have a Sta-Rite variable speed pump P6E6VS4H-209L. it’s leaking at the band clamp. I ordered a new seal U9-228A. After living up the new seal and replacing it the leak is still there. It’s just a drip and it’s not gushing. I don’t see any cracks on the housing or seal plate. I did notice that...

I found the problem. I guess when the pool builder installed the system he stripped the wires back too far. One strand of wire was shorting to the wire next to it. Thanks for the help though.

I have a Pentair easytouch 4 system. The actuator on my intake side started clicking and wouldn’t turn without me helping it. I bought a Intermaric actuator and installed it today. The valves work correctly when I push the valve button. The problem is the system won’t communicate with the...

Thanks for your help. I’ll pick one up

I have a Pentair Easy touch system on my pool with Pentair actuators. When I switch to spa mode one of the actuators clicks and I have to help it move by hand. I assume the gears are shot. Can I replace it with a Jandy actuator? Will those work with my Pentair automation? They are quite a bit...

Do you have any pictures of it?