Search results

Thanks. Will try them. Who I bought replacement manifold from.

Hey all, I’ve had my Digital Autopilot 9 years now. Opened it this season and all is well until today. I was at 3100ppm salt and then today it tells me I am at 0 to 500. Last I checked by drop test I was at 1900 before adding salt. So was like well I guess my probe is shot. So I replaced it...

Thank you. Will just stick to OEM. Odd part is after sitting off last night it’s working fine today. Wonder if the cord is going bad. Cell looks good no edges worn. Just random discoloration on the plates.

Thanks Marty, I did read that, and hoping its just a depleted cell, but I bought a bigger cell than needed and didn't usually go above 25-40% on power on level 1. Anyone ever try the Aftermarket Cells that have the 5 year warranty vs the Autopilot Factory Cells? Few hundred dollars in cost...

Hey all, Been a long time since I posted here, love the community, helped me so much many years ago. Have an Autopilot with a RC-52 ( PC-4 I think now ). Bought it 8 years ago and installed. Yesterday I get a message saying Check Cell, before yesterday, Volts and Amps were perfect...

Thank you. I'll take a look. I only see the screw holding the sensor, where is the nut?

Opened up the pool, and fired up the pump. Seeing water leaking in small beads around the sensor. Is there a replacement seal? Something I can take apart and fix? Or do I need to order a new sensor. Thanks. Wanted to ask before taking it apart.

Crazy as I was about to buy this the other day when opening the pool. Read reviews on the Walmart site, and all stated the same issue. Definitely a product issue.

I have one of these, and been using it for over a year. I love it, causes a nice waterfall effect into the basket allowing it to skim the top of the pool very well. My float broke due to the concrete pad on top of the skimmer basket sinking. Been working great. Can open a close the flow a bit...

Looks like the older American Products fixture, looks exactly the same to mine that is tripping. No water in it, but it's causing the GFCI to trip.

I am having this question right now, as my fixture is bad and tripping the GFCI. I diagnosed it down to the fixture from the housing. I was looking at the Pentair Intellibrite 5G 120V, but so many bad reviews with it failing in a year or less. Anyone have any opinions or longer term...

Well the nightmare happened today when opening the pool. The NJ Winter and Long Freeze took a tole on the pool. I have lost tiles before, and just get new mortar and grout, and fix it up, This time the damage is way more extensive, and the Coping on top of the section is loose. I can pick it...

SO we are having a party on Saturday, and the screws off both of the bottom drains are broken, so they need to be repaired - 10ft deep, and to deep for my belly to hold down and repair. SO... I was thinking..... Let me know if okay to do for temporary. Was thinking about putting...

Have a Pentair Variable Speed Pump. At High Speeds I do not see any air in the basket. If I run at 1100-1500 RPM, I do see that there is Air in the Basket? Is this normal at lower speeds?

Good Evening all, FC: 9ppm ( due to shock ) PH: 7.5 TA - 90 CYA - 110 Salt - 4000ppm Borates 0 (until I put them in) Question, Below are the specs stated for TA and CYA. What are the effects if I leave the CYA at 110 with the SWG? The TA I can adjust by lowering the PH and Aerating, but...

I drained some, since I was worried about the Ladder in the deep end and the ring around the light. I didn't pump out as much as originally planned. If I can get it down to about 4000ppm I will be happy. Will test it tomorrow to see where the levels are at. Thanks

Pump out a whole bunch of water. Then refill with fresh water. I pumped out about a third of the pool this morning. Gave me some time to re-grout a few spots on the tile that needed it. So not a total loss of time. :)

AHHHHHH, wonder if that would be it. I always used Bleach for the past few years. And Chlorine Tabs in the Hayward Chlorinator. I should have checked the Salt level before.

Guess I should have, but thought it would have been 0 since I never added it before.

Good Afternoon All, Well I just opened the pool and added the salt to the pool after setting up SWG. According to the Pool Calcs I have tried, I have between 39-44,000 gallons of water. So I went safe for 40,000. Well I added in all the Salt yesterday, and I added in 25 (40lbs) bags of...

Was told that unless you order the Total Control Solution as a Package you can't upgrade or retrofit it. I just spent the money on the new System, and don't want to have to purchase a new Dig220 all over again to go with the Total Control. The Dig-220 in the Total Control package has a...

Any Suggestions? Looking to place an order today. I was looking at ISIPOOL pH from Aqua Water Systems pH TEK System Hayward HCC 1000

Well I have the Autopilot SWG, and wish I paid attention that the Total Control Solution can't be integrated unless I buy the other Power Unit. So since I am not doing that. I want to have something that Monitors the PH Level and Injects the Muriatic Acid automatically. What are some of...

Re: Finally Done :goodjob: Not sure why you decided to use 3 Jandy valves though :scratch: Wanted a way to adjust the incoming flows. I sometimes when doing a vacuum to waste close off the flow to the one port, otherwise it sticks to the bottom of the plaster, or collapses the hose. But...

Bump on this message to see if anyone had any thoughts on this. I am looking into a PH Solution currently and this was one I came across. I am looking for Automated Solution that Probes and Injects as needed, What do you all recommend for Automated PH Solution

Live in New Jersey

Having a hard time finding out where I can get Muriatic Acid from. When I search, all I find is the Diluted "Green" version? Any idea's on where to find it lately? Thanks

Afternoon all, Some of the Plastic on the underside of the LoopLock Cover is separating from the Black Out Cover. I want to sow this back together, has anyone ever done this? What is the Thread that is used? And Needle Size? Not sure if its all Canvas or Plastic.