Search results

I’ll order some new reagent and try again. I can’t think of what would be causing this either!!

Best by 5/22. I do store my testing stuff indoors and climate controlled areas.

No, nothing else except floats and people. And between yesterday and today not even those.

I think it’s from last season. I’ll check that. I just tested again this morning and after testing at 7.8 yesterday after I added the borax it is back down around 7.2.

No

No chemicals in the pool except the borax I mentioned and the chlorine from the SWG. We haven’t even had much rain. It has been very hot. We do need to add about an inch of city water once every 10 days or so.

The last 3 weeks when I go to test my pool my PH always reads low, like 7 on my Taylor K2006 kit. I add the recommended borax and it’s up around 7.8 later that day. Then the next week when I test again is the same story. I don’t know why it’s running low. Usually it runs high. FC = 5 CC = 0...

VS Omni

I updated the firmware on my system about 2 months ago. Is there anything newer? Yes, the pump on/off has always worked pretty flawlessly. I'm not sure what is going on with the heater or chlorinator. They seem to just continue running as long as the pump is on, regardless of the schedule.

I could do that... I'm really just trying to understand this system.

Also I have tried to call Hayward. They told me they didn't have enough staff right now to help residential customers, due to Covid issues. They said to send an email instead. After multiple back and forths, I never really got an answer to my questions.

It's not freezing yet here, although that'll add another dimension of confusion I'm sure. The heater extend basically just keeps the pump running if you're not at your heat point yet and it is scheduled to shut off.

We've had our pool with Hayward automation for about a year. I am still so confused. I run my pump on a schedule from 8am to 8pm. I have my chlorinator and heat pump both set to run on the same schedule (8a-8p). Chlorinator is set to run at 60% and heat pump at 83. These are the only...

Anyone know how to delete a theme in any of the interfaces? When I go to the panel, I do see a trash can when I pull up the themes, but I'm not sure how to activate it.

My current firmware was 2.22. We had some friends swim tonight and after they left I pulled one of the 5 random usb drives that were still in my pocket and plugged it in. Went into service mode and bam, there were the firmware files. I tried that same usb 30 times earlier. anyway, all worked...

Yeah, I emailed them yesterday. I haven't heard back from them yet. They aren't taking residential calls these days - said they don't have enough techs to handle the volume. :-( Thanks again for all your help. I will come back here when we figure it out.

Still nothing. I'm losing my mind. I've tried 3 different USB drives and 2 of them result in the <USB/> that I cannot drill into and one of them doesn't show anything. I've tried to click/touch on that USB/ a hundred times - nothing. Here's a screenshot.

Thank you for your help. 1. - done 2. - done (and I can see the backup on the USB drive when I take it out and put it into my PC) 3. - done 4. - done 5. - done 6. - done 7. - this is where I cannot click on the USB/ - it just does nothing. I CAN see it there, but when I touch it, it's like it...

Thank you! So I downloaded the MSP and went outside to do the update, however, when I get to the selection of the firmware file, there is nothing listed on the Omnihub display. I have ensured there is no .txt after the MSP firmware, so I don't know what the problem is. The Omnihub is also...

Merged threads - TFP Mod I am trying to add some equipment to my Omnihub and I believe I need a firmware update to enable them. I've scoured all the firmware update posts here and they all say I need to do both the MSP and the MPP update. However, when I look at my system info on my Omni Hub, I...

Hi! Yes I am referring to that part. Directions are here in this post: https://www.troublefreepool.com/threads/new-install-of-omni-hub-aquarite-integration.204579/

I'm returning mine. I really wanted to love it too. :-(

We just installed the daughterboard on our Aquarite to our Omnihub. I can't figure out how to configure the Omnihub to see the chlorinator. The "remotely controlling" light is ON on the Aquarite. Also, when I open the Omnilogic app, I see a notification that says this: "Limit of 0 for AQR...

How did this install go? We are considering the same.

Yes!!

I just realized I never posted our “all done” pics!