Search results

Thank you for that suggestion, I can’t believe I did not think of that. I called my neighbor and sure enough he has a similar robot so I went to grab his power supply and my robot works. I’m going to let it run a complete cycle to make sure it continues. Looks like I can get by with just a power...

I just opened this one up, doesn’t look like there’s much for serviceable parts inside. I disconnected and reconnected all the connections and tried to clean everything up best I could, no results. Just wondering if it’s worth a chance on a power supply, knowing that that robots a few years old...

The fact that I can’t get the power light to come on by pressing the button, makes it difficult to check. The power supply is a couple years older than the robot because the robot was replaced under warranty just before the two year warranty was up so I’m guessing that power supply is at least...

So it started working after unplugging for an hour. Worked a few days - Now it has stopped again. This time however there is no light at all at power supply. I of course checked outlet then removed plug from power unit (short cord) and it reads 120v. So power to the power unit- I then checked...

Thank you!

I should add now that I unplugged it for 30 minutes and plugged it back in the lights on the power supply unit stay on, but still nothing happening at the cleaner. Looks like I’ll have to figure out how to disassemble that S200 so I can check the end of the cord at the motor to see if it’s...

Thank you for the reply, I’m quite sure the power supply probably did get wet out in the rain. But it sat out on my Outdoor Kitchen in the rain all these years prior.

I have a dolphin S200 that’s probably 4 to 5 years old. A couple of days ago we got a whole bunch of rain and I noticed when I went to turn on my cleaner that the GFCI had tripped. This is not the first time that’s happened after a heavy rain. The problem is after I reinstated the power when I...

Up and running- thanks again!

Ordered - thanks for the help and the link. 👍🏼

Thank you!!

I have a clock timer that stopped working. I need to replace it but not sure what model. It has intermatic E10694 stamped on it. It is 220 going into this and I believe 110 output to SWG controller. I am not an electrician, but I feel like I do this job myself by wiring at exactly the same way -...

Thank you for the reply. This is not an old thread actually but I do appreciate the input. I’m really not sure what happened to make it all start working, but I do know when I went to investigate and was going to check with an ohm meter power coming from the switch at the motor connections, I...

RDspaguy, I was talking about the bare copper wire that’s held in place by the set screw. I was about to check the voltage on the motor as you requested, when I noticed that copper wire moved fairly freely. I went to tighten the setscrew, but it was already tight not sure what was going on...

So on inspecting the wiring, I noticed the ground lead did not seem secure. I took a screwdriver to tighten it and the setscrew was already very tight. Not sure if the copper lead had a kink in it or what. So I loosened it and pushed the copper ground wire a bit further through. I then secured...

I just went out and checked, yes the icon does go on and off when I toggle the push button. I will test the voltage, that will be much easier than switching the wiring. I’ll let you know what it shows. What should it read when I have the power button turned on? One question, do I have to...

RDspaguy, here are the requested photos. Currently as I mentioned the circulation pump runs as it is supposed to, the spa Jets come on about half of the time I try.

RDspaguy, I posted those in the wrong order, in my mind I was thinking in the order I was looking at them. (I can’t believe I did that) I actually edited my post to make it correct. You are correct I’m talking about pump 1 which is on the right. That is the pump I’m having trouble with. That is...

OK first my apologies this will probably be a long thread but I want to make sure I am explaining everything thoroughly. I really appreciate any help that I may receive. I have a 2011 Sundance Altamor 880 I purchased brand new. It has an air pump, then it has a button labeled pump II that runs...

We had a little rain last night, but not much. After the overnight chlorine loss test I have 5 ppm, so I lost 1 ppm overnight. Any ideas are welcome. I need to check my CYA, my kit is empty so I will do to pool store and hope for best. Can this have this big of an effect? Cell is clean.

OK, I shut my saltwater generator off and left my pump running and waited 45 minutes, it’s way after dark. as I mentioned earlier, after realizing I only had 1 PPM I went ahead and added some liquid chlorine earlier this afternoon. Just finished testing with the R 0870 DPD: FC = 6 CC = 0.5 (hard...

Thank you for the reply, I will perform the test tonight. The water is crystal clear, I know that doesn’t necessarily mean anything. I will report the results tomorrow, again thank you very much. After I checked the pool and seeing a low chlorine level, I added some liquid chlorine. But that was...

I have a Hayward AQR 15 that is starting on its third cell after I’m guessing 5-6 years. The cell that’s currently on there I had as a replacement, which I ended up never using, but it only had a one year warranty. i’ve had the cell for a couple of years, so there is no warranty on it, all the...

Thank you, now I just need to identify the part number. I think it’s calling for a single speed 2.5 hp motor with a 56 frame, but I’m not sure what all of that means. Tomorrow if I get time I’ll try to take a side cover off and get a good look at the pump. I just found that information by...

OK, tonight I turned on all pumps my hot tub on after running for over 24 hours no problems. Within about a minute the breaker tripped. So I turned on the first pump which does nothing but blow air, worked fine. Shut it off and turned on the second pump which is labeled pump I, worked fine. Turn...

Thank you very much. So far it’s still running with no issues. Overall other than replacing a flow switch this has been a very good unit. I will post what happens with this going forward, hopefully it just continues to run.