ogdento's latest activity

O

ogdento replied to the thread Pump 1: Communication Lost / Pump Status: No Comm!.

@Pieroz as Allen said they are only sold as a matched pair with that key. I wrote a post about how to reset the code on the "Quest"...

Apr 19, 2024
O

ogdento replied to the thread Is the Pentair Easy Touch remote obsolete?.

hey @Jeffrosmit the prices of these things are ridiculous... the Easytouch is obsolete as Pentair is pushing the Intellicenter...

Apr 17, 2024
O

ogdento replied to the thread IC60 & IntelliPH.

D3 and 4 are ESD Suppressors / TVS Diodes (part SMAJ6.0CA)... they can be replaced, along with the 8-pin comm chip to their right. If...

Apr 14, 2024
O

ogdento replied to the thread Pentair Easy Touch LCD Screen.

Looks great! I've switched to an easier way to pull these off, and no longer use an iron and braid or a solder sucker... I have an...

Apr 14, 2024
O

ogdento reacted to Dirk's post in the thread Pentair ic40, surge board, intelliph and swg transformer. with Like.

Whoa there! Can't say I agree with @Flying Tivo completely. (Perhaps he meant red/black, not red/white.) You don't mess with the white...

Apr 10, 2024
O

ogdento reacted to Latitude22's post in the thread Pentair ic40, surge board, intelliph and swg transformer. with Like.

I snapped this photo of my solder job. I did it differently than other folks here. I didn’t want to drop down a wire size so I cut the...

Apr 9, 2024
O

ogdento reacted to Dirk's post in the thread Pentair ic40, surge board, intelliph and swg transformer. with Like.

We would really like to see a picture of that, the next time you're snooping around inside the controller.

Apr 9, 2024
O
ogdento replied to the thread IntelliTouch i9+3 not communicating with Intelliflow VSF pump.

ok, so this means the screenlogic cannot read from the outdoor board... it could be the screenlogic or the outdoor board, but my money...
Apr 5, 2024
O

ogdento replied to the thread IntelliTouch i9+3 not communicating with Intelliflow VSF pump.

from the first post I see that the screenlogic reports firmware 1190, which is the latest... so that won't need to be updated. In...

Apr 5, 2024
O

ogdento replied to the thread IntelliTouch i9+3 not communicating with Intelliflow VSF pump.

on my pool the Intelliflo is wired for continuous power and the filter relay is used to turn on my Aquarite salt cell (which is not...

Apr 4, 2024
O

ogdento replied to the thread IntelliTouch i9+3 not communicating with Intelliflow VSF pump.

i just re-read my post and want to clarify that the personality board diode has nothing to do with the board's "logic supply"... it just...

Apr 4, 2024
O

ogdento replied to the thread IntelliTouch i9+3 not communicating with Intelliflow VSF pump.

just to expand on a couple of Allen's answers... IF a comm chip has failed, it is possible for it to fail in such a way that it can...

Apr 4, 2024
O

ogdento reacted to ajw22's post in the thread Easy Touch Issue? with Like.

AND HERE IS YOUR PROBLEM.... Drum roll PPPlllleeeaaasseee! Valve A should be assigned to CLEANER not SPILLWAY. Your spillway actuator...

Apr 1, 2024
O

ogdento replied to the thread Actuator valve tested good but not working with Easy Touch.

hey by the way... your Itech AC power source is a nice bit of kit!

Apr 1, 2024
O

ogdento reacted to SamsIam's post in the thread Pentair Pumps that work with EasyTouch with Like.

Thanks Jim, You answered what I needed to know. 3HP it is.

Mar 27, 2024

Show older items

Top Bottom

Back