Recent content by g3lo

  1. G

    Have an issue with SWG reading 4000 salt, but Taylor salt test shows 2800-3000.

    Any thoughts?
  2. G

    Have an issue with SWG reading 4000 salt, but Taylor salt test shows 2800-3000.

    What’s strange is when I set the dial to 20 it says check salt, when I set dial to 30-50 it chlorinates with volts 25.5 / 6.10 amps on diagnostics
  3. G

    Have an issue with SWG reading 4000 salt, but Taylor salt test shows 2800-3000.

    Auto to Off: 3800 69 30.3 0.00 26P -0 AL-0 r1.59 T-15 Off to auto: 3800 69 30.5 0.00 26P -0 AL-0 r1.59 T-15 Off 1-min to auto: 3800 69 30.3 0.00 26P -0 AL-0 r1.59 T-15 Cell: TCELL940-CUL I dont have the box and unable to find serial 2800 (14 drops x 200 of...
  4. G

    Have an issue with SWG reading 4000 salt, but Taylor salt test shows 2800-3000.

    cell set correctly in system at t-15 - will get readings and report back. After few days I got it down to 3700. But still high - Taylor kit reads 14 drops (2800)
  5. G

    Have an issue with SWG reading 4000 salt, but Taylor salt test shows 2800-3000.

    We haven’t replaced the cell we cleaned it with acid and replaced last seasons. I dont think it will generate because it’s over the maximum salt level we need it to show below 3600.
  6. G

    Have an issue with SWG reading 4000 salt, but Taylor salt test shows 2800-3000.

    I tried recalibrating the Aquarite SWG, but it won’t go below 4000. Anyway to force system to show 3000?
  7. G

    Aquarite 900

    So I don’t know how or why, but my CYA is 30 and my FC is 10 produced by SWG working 14 hours a day at 50%. I dialed it down to 40%. Does that mean I can keep CYA at 30 or still need to bring it to 70?
  8. G

    Aquarite 900

    Thank you everyone!
  9. G

    Aquarite 900

    I see any specific product that can work?
  10. G

    Aquarite 900

    I’ll get some pics for you and post them. But no, when pump is off, pump is still on, it’s just the RPM is 0 for the time I set the VS to for the night. Hence, the lights on SWG are still on, just shows no flow. Hence, why I thought it’s safe to leave that way since the sensor is built in. I...
  11. G

    Aquarite 900

    So I dont have any automation. I just have a pentair pump and swg. Not sure how its wired exactly. But I assume they are separate. Is there a way to provide a signal from SWG to pump so that when pump is on SWG is on and vice versa?
  12. G

    Aquarite 900

    Do you have any recommendations on a timer that does not break the bank that would turn it off?
  13. G

    Aquarite 900

    When pump shuts off at night, it says no flow, does that mean the SWG is off? And, safe? Or, its still trying to run but damaging?
  14. G

    Aquarite 900

    I dont have automation. But the installer said there is a flow sensor that when the flow is low, it will shut off?
  15. G

    Aquarite 900

    Thank you so much! A coupe more questions: - When I vacuums do I need to turn off SWG? - When I backwash, do I need to also turn off SWG?
See more
Top Bottom
Back