Search results

Hi All, We've had our pool for almost 2 years in July. We have 3 lights in the pool, unfortunately the middle one fell outta sync. By reading this forum my guess is one or two of the LED colors have failed? I've put it in service mode and switched it on / off for 5 seconds in which all 3 reset...

Never actually paid attention to this. I’ve noticed bubbles from a couple returns when the pump typically starts up for the first time in the day, almost like it’s pushing out air bubbles, but then it goes away, but outside of that no. My SWG is only a year old, haven’t cleaned it for the first...

So I got the FC up to 7.5/8 using LC last night around 8:30 tested at 9:30 PM, let it run overnight even with the SWG at 100% just to see if it would produce overnight and stay steady. I had a chlorine loss down to 5.5/6 FC at 7 AM. Water has seemed “crystal clear” for the past couple days, but...

I ran it overnight at 100% and this morning at 10 am, we’re still at 0.5 FC. Hmmmm

Sounds good, this is our second year with it and the summer months have been tricky trying to get the levels to stay sustained only using the Jandy Aquapure 14000 Sounds good, these summer months have been tricky trying to get sustained levels only using the SWG, I know every environment is...

Yeah, it’s trial by error right now, it’s been set at 8.5 hours in the spring with no problem, but obviously the summer heat is different and Wed to adjust. I’m just trying to gauge the sweet point of you will.

Here in North Texas, salt water pool, we’ve had quite the heat stretch the last month over 100 Each day, and our pool constantly gets 11-12 hours of direct sun a day. I’m having to run the SWG at 100% lately just to even TRY to keep up, typically I would be running the pump 8 1/2 hours a day...

I haven’t tried removing the jets. They’re screwed in there pretty good, would need a wrench to get some leverage to get them off. Here is the best picture I have.

Hi All, Quick question, our pool/spa recently got completed in July. We've noticed that when going to spa mode the jets/bubbles don't fully activate unless you turn on the blower first for say 3-5 seconds then turn it off. If If you leave the blower on then you also get the really big extra...

Marty, which do you use on the pool math calculator for liquid chlorine ( I see HD has some and says 10% sodium hypochlorite)?

I only used them for a couple weeks before the SWG was turned on. However here are the ingredients listed

Plaster Yes - Wet Edge - Pebble Finish I have a 35 lb bucket of Chlorine tablets. Can I use those instead? (Pool Time Max Blue 6 in 1) Any reason to go to 10 PPM Specifically?

I have a Taylor salt test kit on the way. Can't be here until Sunday. SWG (Jandy Aquapure 1400 shows 3000). Just happened to take my sample to Leslie's for the heck of it and they showed 1900. Anybody had this far of a discrepancy. I also have a Taylor Pool Kit We have a new pool since July...

Hi Jim We have a Jandy Variable Speed E-Pump (Currently running at 2,000 RPM) I checked the FC level just now and were at about 4.4-4.6 (Pump ran overnight) CYA seems to be between 55-60 as well. I didn't add any stabilizer.

Yes an aqua pure 1400. What do you suggest?

We're about 18,000 Gallons and running the pump for about 10 hours currently. Brand new pool w/ Wet edge pebble on July 7th. I'll definitely start using Muriatic acid in the future. Original PB left a handle of stabilizer that I still have a bit left of.

How is one getting the FC levels to 4 or 5 with a SWG? We just had our new build converted yesterday and FC levels are at 1.8 at 85% output with the Jandy Aquapure PLC 1400. Tested with a Taylor K-2006c kit TA - 90 CYA - 30 (Just had about 1 1/2 days of rainfall. FC - 1.8 PH - 8.0 (just put...

Wet Edge Cadet Blue Plaster on 7/7 Acid Washed on 7/8 Filled on Thursday evening finished Saturday morning 7/10. We returned home on 7/12 and the pool was 102 degrees. They test fired the heater and forgot to turn it off Hope all will be well. They also threw in a Polaris, which never ran that...

Plaster 7/7/21 - Were out of town in the Bahamas but watched them through the camera (Wet Edge - Cadet Blue)

Hey Tom. The company that did it is below. Let me know if any other questions! http://www.decorativeconcreteincorporated.com/services.html

It’s about $4/sq for for the multi colored, we priced in the single color texture which was $3 but I saw the multi colored on their website (Dallas area)