Search results

  1. H

    Broken Bolt for Ladder Anchor Wedge

    I'm trying to identify a replacement part for this wedge that holds in my in-ground pool ladder or should I simply go to the hardware store and find a matching bolt to replace the broken one? Pictures of the broken bolt & wedge attached.
  2. IMG_4962.JPG

    IMG_4962.JPG

  3. IMG_4961.JPG

    IMG_4961.JPG

  4. IMG_4960.JPG

    IMG_4960.JPG

  5. IMG_4959.JPG

    IMG_4959.JPG

  6. H

    Jandy AquaPure & PLC1400, No Flow

    SOLVED: Today, my new Jandy SWG sensor arrived. Quick install to my control box and onto the SWG cell. Turned on the system and a couple moments later, I have FLOW, 3.1 salinity, 84 degree pool temperature. It's now generating chlorine and acting as expected. Filter PSI sitting at 8...
  7. H

    Jandy AquaPure & PLC1400, No Flow

    James W: Thank you again for the advice. If I simply cycle the system, I get no errors. The panel displays "Wait" and hangs. I can't do anything. I shut off the system, opened the panel, disconnected the connector to the flow sensor. Test 1: Pressing the Salinity and R-temp buttons (on...
  8. H

    Jandy AquaPure & PLC1400, No Flow

    I'm sure it's time to replace them both. Do you buy from Amazon or somewhere else? I got these when my pool was originally built so I'm not sure if there is a best pool supply site.
  9. H

    Jandy AquaPure & PLC1400, No Flow

    Great! Thank you for this information, I'll try it tomorrow morning before I order anything!
  10. H

    Jandy AquaPure & PLC1400, No Flow

    Today I continued troubleshooting. Symptom stays the same: When I turn on the system, the Sensor Module Indicator will briefly light up either PGM A or PGM B and then all lights go off. At the same time, the SWG Management Panel locks up showing 00% chlorine and "Wait". Can't use any buttons...
  11. H

    Jandy AquaPure & PLC1400, No Flow

    Update: Today I emptied all the skimmers and pump basket as usual. Cleaned the 4 Pleatco Cartridge filters & new manifold (picture attached). PSI still sitting around 7psi, waterfall and the water jets in the pool all are pushing water strong. Now, I turn on the system and the Sensor Module...
  12. Manifold n Pleatco.jpg

    Manifold n Pleatco.jpg

  13. H

    Jandy AquaPure & PLC1400, No Flow

    Also, new info: The Sensor Indicator Module image above shows Green for Sensor Flow but it's actually Blinking On/Off today. That's new/different than what I've seen before. Main panel still shows "No Flow" and no error messages.
  14. SWG1.jpg

    SWG1.jpg

  15. PumpFilter.jpg

    PumpFilter.jpg

  16. PSIJun.jpg

    PSIJun.jpg

  17. FlowBLINK.jpg

    FlowBLINK.jpg

  18. H

    Jandy AquaPure & PLC1400, No Flow

    I'm really hoping to find a solution to have this SWG last one more season because my budget is very tight with this whole pandemic situation. This SWG is over 5 years old at this point...but never had a problem yet. Yes, I know they usually don't last beyond 3-4 years but please read on...
  19. NoFlow.jpg

    NoFlow.jpg

  20. ProgramB.jpg

    ProgramB.jpg

  21. Control Board.jpg

    Control Board.jpg

  22. H

    Jandy Aquapure No Flow

    Thank you. Tried it twice but didn't make any difference.
  23. H

    Jandy Aquapure No Flow

    I'll give it a try. If that doesn't work, I'll create a new post.
  24. H

    Jandy Aquapure No Flow

    Did you get this solved? I am having the same problem this year. The Salinity is measuring 3.1, pool temp 78, but No Flow. Using the Jandy PLC1400 and AquaPure control panel. Hoping maybe I don't have to replace my SWG cell.
  25. H

    Very Green Open, 1st time in 6 years

    I think for safe measure I'm going to take out the ladder & power wash it.
  26. H

    Very Green Open, 1st time in 6 years

    I can see the bottom now and everything I've been missing vacuuming blind.
  27. May 30 Morning1.jpg

    May 30 Morning1.jpg

  28. H

    Very Green Open, 1st time in 6 years

    Looking so much better already!