Search results

  1. 1617555639439.png

    1617555639439.png

  2. caliskier

    I saw T-Cell-15s on Amazon end of season last year for $399, now $599. Should have pulled the trigger, where do you get yours cheep?

    Humm, that is a good point....i cant prove that either way. What you see below is the Hayward sold item which was a little more... analysis via camelcamelcamel...
  3. caliskier

    Jandy Lite 2 Electrical Problem with a FL-5 but incoming power is good at 123V and 123V for A and B screws

    Ok, if I hold the enter key for 7 seconds it clears everything... But in about another 7 seconds the FL-5 comes back. It is supposed to clear automatically once the power is restored. All voltages that I can tell are correct, so this is confounding. The only other thing I can think of is...
  4. caliskier

    Jandy Lite 2 Electrical Problem with a FL-5 but incoming power is good at 123V and 123V for A and B screws

    Checked it, both sides of the pressure switch are working, 27 VAC
  5. caliskier

    Jandy Lite 2 Electrical Problem with a FL-5 but incoming power is good at 123V and 123V for A and B screws

    OK, Will check it tomorrow with the water flowing, but would that cause the brownout error code?
  6. caliskier

    Jandy Lite 2 Electrical Problem with a FL-5 but incoming power is good at 123V and 123V for A and B screws

    Thanks! 220 coming in How do you check that? Put one probe on A and the other on B?
  7. caliskier

    Jandy Lite 2 Electrical Problem with a FL-5 but incoming power is good at 123V and 123V for A and B screws

    Hi I have the FL-5 error code which usually means a brownout or low power condition. I have given it the 3 min to reset itself and still an issue. I have tested the incoming power at A and B and reads 123V and 123V. Every reading from step 1 to 6 is not 24VAC but 27VAC, not sure if that makes...
  8. 1603582382144.png

    1603582382144.png

  9. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    IT WORKS!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! I have edited this a few times for some minor issues. Need to get the salt in the pool, get the levels right and go from there. For now, my wife is smiling and all is well. Thanks for your...
  10. caliskier

    Heater Problems: Jandy Lite 2 FL 3 Error Code - Means its detecting a flame when it should not be. There is no flame. Is it the board or the sensor

    Hi brother, here is the video I mentioned that might work to fix it... I have not tried it yet but I think its the same concept. You and I probably have a dirty flame sensor and its a safety feature where it thinks the furnace is blowing out gas when its actually burning. You just need to clean...
  11. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    WOW. wow wow wow... I just didn't see it in the dark. Not sure if it was reading C0d3Sp4c3's post or red beards post a couple of times, but I went out to it this morning and decided to unscrew everything, I did not see that the little clips were actually set up for 120, i did not even know they...
  12. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    Thanks, BTW Can I just go to 120V with this unit and plug it directly into the wall socket that happens to be immediately below? Its a Intermatic ET1125C. I believe it allows for two different loads. I typically don't have an electrician do any work for me, but we were leaving on a trip...
  13. 1599185787874.png

    1599185787874.png

  14. 1599185701470.png

    1599185701470.png

  15. 1599185609945.png

    1599185609945.png

  16. IMG_0240.jpg

    IMG_0240.jpg

  17. IMG_0238.jpg

    IMG_0238.jpg

  18. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    It does not like something I did, keeps throwing the breaker. I installed it exactly as the directions said, jumper and everything. My setup is a time clock and a 1.5 HP pump on 240v. I have the wires on the hayward side at 1 and 4, there was no jumper so I added a wire before I gave it...
  19. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    Thanks red-beard, I almost screwed that part up, the PVC part. Bonding system? My pool does not have one, or at least I don't see a ground wire comming off the pump to somewhere else. I just have the typical ground. Do i need this bonding wire?
  20. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    Thanks all... Additional question(s) as I am using the labor day weekend to begin the install process... Hayward directions say: If the pool does not have new water, add 1 quart of metal remover and algaecide. I get the non-copper algaecide, in case the system does not chlorinate well it does...
  21. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    Thanks MK, curious why not Clorox? where can I find plane water softener salt? How much? and in what unit of measure? Thanks for the rest of the help, very informative.
  22. caliskier

    About ready to install a Hayward W3AQR15 on my 20,000 gallon pool, questions about how to make sure I don't screw up and get a green pool

    All, So about to get this baby hooked up. I have read two pool school articles about what it is in general and how to water balance so I think I will be able to roll once I get it hooked up from a PH, CYA perspective, but I have some general questions of ignorance. 1. What salt do I buy, just...
  23. caliskier

    What is the difference between the Hayward W3AQ and GLX-CTL-RITE?

    OK, I know I don’t need automation, I want Automatic testing which does not really exist. I read some posts about the pHin, all that is is a great business model to get money from people that don’t know what they’re doing.