Recent content by smooth2222

  1. S

    PAL 2000 not working correctly. Options?

    Did you ever solve your sync problem? I have the exact same problem. Always have to turn it off and back on with the remote, only to happen again a few minutes later.
  2. S

    Looking to replace sand filter, Pentair vs Hayward

    was looking at the Pentair ccp420 420sq Pentair ccp520 520sq Hayward c4030 425sq Hayward c5030 525sq Is 1 brand better than the other? Assuming the prices for cartridges are the same to replace for them? Any information between the 2 much appreciated.
  3. S

    Just cut solar cover to fit!

    Meadow, does the cover lay completely flat on the water everywhere? Also when you cut it, when you put it back onto your pool, if part of the cover is overlapping the other part, it gives the wind something to catch and lift it up. I would assume only half is flying away?
  4. S

    Optimal pool filter pressure?

    If your running at 0 pressure, how do you know when to clean the filter? 1000 rpm you guys running 24/7?
  5. S

    Optimal pool filter pressure?

    Just installed a VS pump, What is the optimal pool filter pressure? As i can adjust the rpm to get any pressure i desire, so what is the optimal? From what i been reading i,m seeing 5-15psi and 10-20psi? What is the optimal?
  6. S

    Just installed my new VS pump, need speed suggestions.

    So 2075 rpm, maybe you got the sweet spot? Seems like you cant go to lower or you wont have much pressure, See what other people chime in and say.
  7. S

    Just installed my new VS pump, need speed suggestions.

    Yeti what is your pump gauge pressure at that rpm?
  8. S

    Just installed my new VS pump, need speed suggestions.

    V-green 1.65. 1.5hp VS. 10.5 amps Original 1.65. 1.5hp. 16 amps Orignal single speed pressure gauge 20psi, same with the new one. 3450rpm,s Is there a pressure on should aim for? 2600 rpm im at 10psi 1850 rpm,s i,m at 4psi 1350 rpm's i,m at 1psi Obvious lower rpm and longer...
  9. S

    Piece of tile fell off around the pool.

    The current one is more of a rubber flexible silicone. Any idea?
  10. S

    Piece of tile fell off around the pool.

    Wanna try and use what they original used so the white matches somewhat.
  11. S

    Piece of tile fell off around the pool.

    Tile that goes around the pool fell off, inground pool. Current white glue. What time of glue do i use? Also does it need to be dry or can you do it wet? Would only have to drain a couple inches since the tile is on top. Anyone have a link? Assuming some type of white silicone special too...
  12. S

    REplacing pool motor, anything I should know?

    I don't have a gokit, do you recommend replacing all the seals? is this brand good enough? and contain everything I need? could not find a gokit brand...
  13. S

    REplacing pool motor, anything I should know?

    just bought this, A.O. Smith 1.65 HP Variable Speed Pool Pump Motor Square Flange - ECM16SQU - INYOPools.com ao smith 1.65hp variable speed motor square flange. Should pay for itself in about 2-3 years. Is there anything I need to know about installing this? seems fairly easy?
  14. S

    Pool closing question

    Yes it defiantly reduced the amount of worms and leaves, i would say about 50-75%. Used a 1/2 thick rope. Made it a lot easier to open the pool.
  15. S

    Anyone have this AO smith vs pump 1.65hp

    A.O. Smith 1.65 HP Variable Speed Pool Pump Motor Square Flange - ECM16SQU - INYOPools.com Curious if the user controls are easy to use? How the timer works?