R
Report

RDspaguy

In The Industry
Well-known member From Cabool, Mo
Messages
2,038
Media
134
Featured content
0
Reaction score
1,127
Points
0
Joined
Last seen
Follow
Start conversation

Latest activity Postings Media About

    • R
      RDspaguy replied to the thread Spa pump going bad?.
      It could be a suction-side slice valve. They are known for sticking on older tubs. Sometimes the handle pulls out of the top. You can...
    • R
      RDspaguy reacted to JoyfulNoise's post in the thread Teeny Tiney Bubbles with Like Like.
      What you are describing sounds an awful like cavitation caused by rapid and intense changes in the momentum of the water such that voids...
    • R
      RDspaguy replied to the thread Teeny Tiney Bubbles.
      But this isn't foaming, it's fizzing. There is no foam, but the water does cloud with the injected air and it fizzes at the surface. As...
    • R
      RDspaguy replied to the thread Teeny Tiney Bubbles.
      That's a fascinating video, and on-topic as it shows in extreme slow motion an effect that highly resembles the one under discussion. I...
    • R
      RDspaguy reacted to Mdragger88's post in the thread Magic Eraser Use with Like Like.
      Microfiber rags for the win here- they help scrub but don’t scratch & they grab & hold instead of pushing stuff around. They also don’t...
    • R
      RDspaguy replied to the thread compatible filters?.
      Sundance does not use a filter housing, they use a filter well moulded into the shell. There is no housing that will fit a SD filter...
    • R
      RDspaguy replied to the thread Bullfrog hot tub.
      Not if it's from the dealer. DIY is another story. Old spas that were not plumbed properly to contain the ozone until depleted and...
    • R
      RDspaguy reacted to Jimrahbe's post in the thread Easy touch for 2 heaters? with Like Like.
      RD, The EasyTouch does not have "dual equipment' controls... The IntelliTouch does have a dual equipment" circuit card, but you would...
    • R
      RDspaguy reacted to 1poolman1's post in the thread Easy touch for 2 heaters? with Like Like.
      You would need to get the power-center as well as the kit.
    • R
      RDspaguy replied to the thread Easy touch for 2 heaters?.
      And with the electric heater I can use a relay and feed it off the board, or do I need to feed the low-voltage gas heater connection...
    • R
      RDspaguy reacted to 1poolman1's post in the thread Easy touch for 2 heaters? with Like Like.
      An existing EasyTouch? Pentair makes a dual-equipment Intellicenter upgrade for the EasyTouch...
    • R
      RDspaguy replied to the thread Easy touch for 2 heaters?.
      No, upgrading an old pool and spa running on hardwired components.
    • R
      RDspaguy reacted to NeedPAPoolHelp's post in the thread New swim spa cover with Like Like.
      We went to a dealer who sells them-drove an hour each way. Using it is very convenient. Seems quite durable. The dealer is a family...
    • R
      RDspaguy replied to the thread Bullfrog hot tub.
      Yikes! Ok, no time to read all of that right now so forgive me if I repeat anything somebody else said. To be clear, what I advise are...
    • R
      RDspaguy posted the thread Easy touch for 2 heaters? in Pool Automation.
      Any of you easytouch pros out there know if I can get an easytouch to run a pool and spa with separate equipment, spa heater is...
    Show older items
  • Loading…
  • Loading…
  • Loading…
Top Bottom
Back