Hi All,
I would like confirmation or correction if possible, before I dig up the yard to trace back the underground supply side lines for a leak. We can't get the pump to reprime after shutting it off and I can't tell if the problem is a leak in the line, a clog in the line from an errant toy being sucked in, or if there is a problem with the impeller. Here's what has been done:
1. When I turned the pump back on the other day, it made a humming noise, like it was trying to get going but couldn't. I turned the power off and then on again, at which point it made a single click and then nothing. I disconnected the motor and took a look at it. The impeller seemed tough to turn by hand. I pulled a bit of hair and gunk out, but not much I thought. There seems to be a lot of wear on the end of the impeller, where it fits into the diffuser (?) body - concentric rings or grooves - I don't think they look like they're intended or molded into the piece. I tried to take the impeller off (following the instructions on a video and on this forum, but the impeller was on too tightly for me to continue - I couldn't loosen it by hand and didn't want to break anything by reefing on it or using the tool I use for removing oil filters.
2. Because of the click, I took it to the electrical shop, where they confirmed the capacitor was blown. They replaced it and tested it (with the impeller/head assembly on) - the motor turned and sounded fine so I brought it home and reconnected everything. When I flipped the switch, the pump started up fine and sounded okay, but I can't get suction to start.
3. I can get a very small amount of water to draw from the skimmer basket side, but not enough obviously. I have tried:
- covering the intake at the bottom of the basket with my hand to create vacuum - nothing.
- putting the hose down the inlet and running the tap full bore - nothing but a few bubbles from the jets.
- re-opened basket lid and refilled basket at pump - closed and tightened the screws. (not a seal problem there, checked by pouring water over it).
- tried the 25 foot toilet snake/auger and encountered nothing, but could not be 100% sure because the snake could not get beyond an S-turn in the line. I went at it from both ends of the line, though, and the auger head was gunk free each time.
4. There is no loss of water over time in the pool, and there was none when the pump was running, so I don't think it is a cracked line between the skimmer and the pump house. Besides, I've had cracked lines from under the skimmer basket before and we had sand leaking into the system then.
Does it sound like there is still a problem with the impeller being clogged or is it possible there is a problem with the motor not turning fast enough? I don't think it is the latter but I am also out of ideas at this point, so any help would be appreciated.
Thanks in advance.
I would like confirmation or correction if possible, before I dig up the yard to trace back the underground supply side lines for a leak. We can't get the pump to reprime after shutting it off and I can't tell if the problem is a leak in the line, a clog in the line from an errant toy being sucked in, or if there is a problem with the impeller. Here's what has been done:
1. When I turned the pump back on the other day, it made a humming noise, like it was trying to get going but couldn't. I turned the power off and then on again, at which point it made a single click and then nothing. I disconnected the motor and took a look at it. The impeller seemed tough to turn by hand. I pulled a bit of hair and gunk out, but not much I thought. There seems to be a lot of wear on the end of the impeller, where it fits into the diffuser (?) body - concentric rings or grooves - I don't think they look like they're intended or molded into the piece. I tried to take the impeller off (following the instructions on a video and on this forum, but the impeller was on too tightly for me to continue - I couldn't loosen it by hand and didn't want to break anything by reefing on it or using the tool I use for removing oil filters.
2. Because of the click, I took it to the electrical shop, where they confirmed the capacitor was blown. They replaced it and tested it (with the impeller/head assembly on) - the motor turned and sounded fine so I brought it home and reconnected everything. When I flipped the switch, the pump started up fine and sounded okay, but I can't get suction to start.
3. I can get a very small amount of water to draw from the skimmer basket side, but not enough obviously. I have tried:
- covering the intake at the bottom of the basket with my hand to create vacuum - nothing.
- putting the hose down the inlet and running the tap full bore - nothing but a few bubbles from the jets.
- re-opened basket lid and refilled basket at pump - closed and tightened the screws. (not a seal problem there, checked by pouring water over it).
- tried the 25 foot toilet snake/auger and encountered nothing, but could not be 100% sure because the snake could not get beyond an S-turn in the line. I went at it from both ends of the line, though, and the auger head was gunk free each time.
4. There is no loss of water over time in the pool, and there was none when the pump was running, so I don't think it is a cracked line between the skimmer and the pump house. Besides, I've had cracked lines from under the skimmer basket before and we had sand leaking into the system then.
Does it sound like there is still a problem with the impeller being clogged or is it possible there is a problem with the motor not turning fast enough? I don't think it is the latter but I am also out of ideas at this point, so any help would be appreciated.
Thanks in advance.