Search results

I just noticed small orange spots all around the pool. They will come up with wire brush scrubbing but not easily like algae. They are spread around, no metal found in the pool. Have not added water in a long time, otherwise, just rain water. Maybe 250-500 gallons about a month ago. Pool is...

So it seems that the difference between the S200 and S300 is just the wifi/bluetooth and use of the APP. Is there anything else. Trying to figure out if this is really worth it? Typically I like automation and things that can be controlled via app but it is not always more convenient or...

Have EasyTouch 8 with Indoor Control Panel I run my pool 10-5pm normally. I check my chemicals usually around 8pm. If I need to add Muratic Acid or Chlorine to supplement the SWG, I would like to run the pool for 1 hour. What are the steps to set an Egg Timer to run the pool for 1 hour. I...

I did not think I would have this issue since the tap water is about 350-400 expected to be filling regularly due to evaporation and thus have the CH going up, rather than down. CH has dropped to 275 due to alot of rain and splash out. I have only had to add a little water a few times. FC 8...

Theory: Running the SWG during a SLAM could make the SLAM end sooner and reduce the amount of bleach needed. Caveat: Can't have it running during a OCLT. So I had to do a SLAM last weekend. Since I understood how much FC my SWG was producing, I keep it running all during the SLAM, 24 hrs a...

I just got the Cyanuric Acid Standard 50 ppm solution. Added Standard 50 ppm solution (R-7065) to the sticker, then added CYA Reagent (R-0013), shake wait 30 seconds, shake again, then test. Sun to my back at waist level. Ran the test 2 times with new reagent each time. Both times, the dot...

What is the SWG Run Time Calculator? A tool that is designed to answer the common question of "how long should I run my pump/SWG". It calculates the run time of your SWG and Pump based on your pool size, the output of your SWG and your daily FC PPM loss. It is designed as a starting point...

After a big costly mistake culminating on Sunday (I killed my entire newly sodded back yard - another story for another time), I told my wife, it was just probably going to be one of those days. I have a SWG but we had alot of rain on Sat and swam alot with usually 8-9 people in the pool. So...

Just posting this for informational sake as I wanted to understand exactly how the % worked. Question: What is the on/off cycle time for the Intellichlor? For example, if set at 50%, does it cycle on for 1 min, then off for 1 min or 1 hr on/1hr off, etc. I would like to understand this for...

I would like to add Borates but I understand that I need to be sure that TA is correct first. What parameters are used to determine that TA is "optimal" for my pool? Is there something I can read? I understand how to adjust it and its role but not sure I understand when to know it is...

Am I missing something or is there a mistake one one of these? In pool Math for a SWG pool, it recommends a target of 9 with a CYA of 60. On the Pool School - Chlorine / CYA Chart it recommends a target of 4 with CYA of 60.

Ok, starting to feel stupid. Something went wrong. FC 0 CC 0 PH 8.2 CYA 70 TA 80 CH 300 Pool is clear. The only thing different is that I added ProTeam Metal Magic initial dose for a new pool since the concern that PB provided it and expected it to be used for warranty purposes...

Tampa, FL Full sun from about 1130am Screen enclosure Firing up SWG this weekend Based on everything that I have read and the recommendations for Salt Water Systems in full sun I need to be at the high end of the spectrum do you agree? Thank you

My pool builder provided algaecide and metal magic at startup implying I needed to use those. what is the reason for those at a start-up of a pool and I'm assuming I really don't need them but want to check.

I have read the instructions several times and I just don't get the practical application of the START and RUN values. Also, validating that the Set Temp would be the temperature that I want to pool to be at but then the Max temp is when it should shut off. ??

I can see it in the mouth is the unit. Any idea on what to do without tearing up the opening?

I am starting to plan out the different features that I want to program. I have 2 valves for 2 waterfalls that I can put a actuator on. I wish the were on one valve that I could turn on/off and then use the valves behind the water feature to control the individual flow. Anyway, I will...

I have been taking reading everyday to ensure that the Chlorine and PH are correct. A few days ago I started working on bringing the CYA up using granuals. I noticed the TA was lower than before probably due to the Muratic Acid pulling it down. I was using some pucks to maintain things for a...

My PB installed a overflow that opens out into what will be a landscape area and then it will drain off into a low land area and as it drains will pass through the plants and st. augustine grass. Will the salt / chlorine water kill the plants and grass? If so, I guess I have some work to do...

Just started up on Thursday night. I have been going to the local pool store to get the water tested so that I have easy proof of the management of the chemistry. We added acid and keeping the PH in line pretty easy. Pebbletec said to add chlorine after 2 days. We did a initial shock of 1...

Title line says it all. I see that Jandy recommends it but does not require until a separate pump is being used. Our descents are part of the primary filter system. Now is the time to install if it is needed before we fire up the pool. We will be delaying starting the decent for a while...

My PB by default installs the Intellibrite LED light and the Intellibrite Controller. My PB by default installs a basic timer control and hayward equipment... I had him change / upgrade to all pentair equipment including the EasyTouch 4PSC-IC40 - Single Body (includes SCG integration & IC40...

So a few of you may have seen a sketch and PB comparison but I am not getting down the final list and design after choosing our PB. The pool builder that i am using is allowing me to choose my equipment and I can design whatever I want without affecting price as long as it is under 400sq...

I would assume that the actuators are generic but just want to be sure. I am specing out a Pentair setup but the PB is using Jandy valves. Does it matter if we use a Pentair Actuator with Jandy valve or Jandy Actuator with Pentair EasyTouch. Thanks.

We are planning a Florida New Pool Build and had settled on the Pentair Intelliflow. We will have the Pentair SolarTouch Solar Control System. Pool will be 12,500 gallons No spa 2 Bubblers 2 Sheers Solar on 2nd story A further research is leading me to believe that based on the cost of the...

So that pool builder that I am working with is allowing me to choose whatever brand of equipment I would like. He usually uses Hayward and that would probably be fine but if I have a choice.... and the solar contractor that I spoke to recommended against the Hayward VS pump due to difficulty...

New IG pool build in Florida. 2 Story House with large roof facing SSW, will have a Pentair VS Pump. PB says " The automatic control for it is a waste of $$ " - I have not spoken to him yet to find out why he says that but plan to. On a 50k total pool build another $300 is not that much...

We are scheduling the pool build and want to be able to swim by Mar 1st. So once the build is finished and water goes in, is there a waiting period while water is stabilized, everything settles in....

Ok, its PB comparison time. Time to make a decision. If money were not an issue, I would go with PB 1 for sure but we are already well beyond what we initially thought. We can do them all but the most expensive one will dig more into our savings than we want to. My hesitation with the PB 2...

I am currently getting quotes for a new build . what do I need to be looking for in regards to a pump that will support solar on a two story home. Sent from my SM-G920V using Tapatalk