Search results

Got 3 years out of my PB4SQ before pump housing failed. Polaris wouldn’t stand behind by the unit when contacted. Feel they should be offering a recall for a defective design, plenty of companies do the right things these days. Overall liked the PB4SQ as a booster pump for efficiency and good...

I did a Pentair conversion w/ 522046 back in Oct 22 to upgrade from Easytouch to Intellicenter. All has gone well and pretty happy with system. Came back from out of town yesterday and noticed pool cleaner running when it shouldn’t. The pool main pump is running fine on its schedule, just...

I replaced $50 worth of breakers yesterday. My Easytouch was wired to power each relay from a sub panel breaker with 240v 30a dual-pole running the filter pump and booster pump, 240v 20a dual-pole running Superflo for waterfall, and 120v 20a single pole running easytouch and pool light. I...

Pics of salt card

Appreciate the help Mr. Jim. I went through the Easytouch 8 yesterday. This is a 2008 production version with breaker buss in the lower middle of the cabinet. I removed the salt cell and wired Pentair controller from the data port, and it made no difference. The Intelliflo still is running...

Appreciate the comment Jim - you are correct. When working correctly the Intelliflo reads ‘Display not Active’ if connected to the data cable. I’ve removed the cable ends at the pump and automation, used contact cleaner, and no go - pump still runs on its own. even though the pump is only 6...

Could use some pro advice - We have a 35,000 gal salt water pool without spa built in 2009 in Houston area. Easytouch 8 automation drives a Intelliflo for filter pump, whisperflo pump for water fall and Pentair booster pump for cleaner. The wired Easytouch inside the house panel currently...

The desire for the new/updated software is not for just the 8 speed options, but to also provide the ability to possibly control a 2nd Intelliflo someday. Easytouch can support two pumps, but my Easytouch version (UOC 2.010 / UIC 1.060)only offers (1) Intelliflo 4 option, where the newer...

I installed the Multicyclone Waterco 16 a week ago during a pump replacement and I'm really impressed with the amount of sediment it collects. My pool is salt water and has flag stone bench and waterfall, so I get a fair share of sediment on the pool bottom. My pool cleaner moves around and...

Thanks again for the interest and info JasonLion! I'm just trying to have 8 speed options, and currently my Easytouch when I go to 'SETTINGS' shows a 'INTELLIFLO 4' option for setting speeds, and allows 4 speed options 1/4 - 4/4. If I put the Easytouch in SERVICE mode, the Intelliflo (on-board...

UIC: 1.060 UOC: 2.010 This is the software my Easytouch system has installed if this can help answer my Intelliflo options of only 4 versus 8. Emailed Pentair and they say I need to replace my inside wired Easytouch 8 controller ($275 online) to fix the issue, but I'm not convinced they...

Thank you all for your replies and info. Thought I'd give some feedback from installing a new Intelliflo VS pump, Polaris booster LA-MS05 pump, Waterco Multicyclone 16 pre-filter, installed new Kreepy Krawley Platinum for broken cleaner, and relocated my 2hp Whisperflow with recent motor over...

Thank you JasonLion. Makes perfect sense. I was making this much too hard in my head! I'll post pics of the new Intelliflo setup when I get done with the install. Hoping the new Waterco pre-filter does as advertised!

Jimrahbe - I'm out of town so I don't have pics available on me. I seem to remember That all of my pumps are on relays inside of the Easytouch cabinet. I apologize as I'm trying to explain all of his from memory. I was hoping that there was a standard 220v main breaker inside the Easytouch...

Thank you for the reply, JasonLion. My question is really that I'm expecting when I install this weekend that I will disconnect the main pump's conduit/wire from the load side of the Easytouch pump relay, and where exactly should that end connection be moved to get constant power? I'm hoping...

I have a 26K gallon salt water pool that is 6 years old run by a EasyTouch 8 automation system. I'd like some help in understanding the wiring of an upgrade I'm doing. I have (1) 2 1/2hp Whisperflo for the main pump, 2nd 1hp Whisperflo pump for waterfall, and Polaris 3/4hp booster for the pool...