Search results

Holy c**. We did not know that. Thank you very much for that. This changes many things. Like forget the pump/motor thing. Jim

Interesting. I will check this out and see if possible. Thank you. Jim Happy 4th.

Correct. Floor returns are nozzles that pop up and rotate, sort of sweep effect to floor. About 3" wide/1" height. Wall nozzles come from 1.5" pipe with a 1" fitting attached to end. Floor and wall nozzles are controlled by Paramount water valve which controls flow to each nozzle in sequence...

No in floor cleaner. Sorry

What do you folks think about this pump for my needs? WFDS -4

Hello Bama, Its 240. Jim Also have 55' of pipe from pump pad to valve that controls floor and wall outlets. Two return lines of 1X1.5" and one 2". Two suction lines of 2" pipe. One from skimmer(55' to pump pad), one from main drain(35' to pump pad). Hope this helps.

Added Image of Motor Label.[attachment=0:17ra69rg]Pump_Label.JPG[/attachment:17ra69rg]

Home built 1997, we purchased in 2000, Not sure of what pump/motor I have as motor has been changed by pap several times over the years, as recent as May this year. It seems that motor exchanged with same as before 1.5HP SF 1.1 with no consideration for efficiency, needs or electrical use. Have...

:-D All comments appreciated. Thanks Jim

Thanks everybody. Looking at sand filters, these two: Hayward S244T Pro Top Mount 24" with 1.5" Vari-Flo Valve and Triton II TR 49 GPM 2.46 SF and I think 2" Hi Flow Valve Side Mount. Please comment on these two items for me to consider. Any comments on using Zeosand? Do I have too much...

Thanks every one. Helpful input. Any experience with Jandy CS200? Jim

Today noticed leak on backside of PXC125 filter about 1 inch below intake port. Stream is the size of small needle. Was going to replace with same however they say that this model has been discontinued. So maybe now is good time to try something better. No problems, however. How say you Sand...

Have checked and rechecked all systems appear to be normal. So looks good. Latest numbers follow. Thanks for all help. FC 8.0 CC 0.5 TC 8.5 TA 75 CH 275 CYA 80 PH 7.5 This was with 60% setting have reduced to 40%

Thanks for the tip. After looking inside box, removed cover panel, noticed that pc board holding lcd was not secure, then noticed that of 7 pins that should have been inserted into lower center of same only 6 pins were properly attached, corrected and system came alive. Also used your procedure...

Installed new AQR T-9 today and all is well except that unable to select type of cell and no Lcd display. Tried to set switch to auto press diagnostic button repeatedly and no response. Also top four lights are blinking green, next three also blinking red, last one blinking amber. Have tried...

Here is latest test results: FC 9.5 CC 0.5 TC 10 PH 7.2 TA 75 CH 250 CYA 70 SALT 3600 with K-2006 SALT 2910 with AquaChek sticks Confused as to why FC jumped from 4.5 to 9.5 when only change was CYA from 30 to 70. Any ideals? Would I be safe to install ARQ SWG now with these numbers? Thanks. Jim

Hey guys, what do you think of this. Finished my weekend project which was adjusting numbers so that I could do Borax application and salt pool for SWG install later this week. Here are numbers after Borax and Salt added to pool water. Borax sticks are on backorder and should have CYA refreshed...

Going to Borax application then SWG. Just trying to get numbers in order first.

Good suggestion. However I did pick up parts today to make aeration device, now need to figure out how to connect to wall port. Its a 1" outlet flange attached to what I think is 1.5" pipe. Not sure just yet. Trying to get correct numbers for Borax application then add SWG. Thanks for your...

Thanks for quick reply and links Jason. Looks like Aeration for me also. Thanks again. Jim

TA is 125 PH is 7.4 How do I get TA to 80 and not change PH? If MA is added TA is reduced and so is PH. What is the best way? Thanks to all. Jim

"If you and fit between the pipe pairs, I would certainly shift the filter and pump over to line up and have fewer turns." Thats one of my goal. Not sure of space. May need to shift filter to right of pump or couple 45's. Just found new problem, which is: Have 6 wall outlets and only one is...

Second group of images for poolman and others to view. Thanks Jim

Additional images for Poolman and others to view. Thanks Jim