Search results

Sorry for the delay, thank you very much !

can you point out the K4 relay?thermistor ? just so o know what is being referenced( and i can compare to mine)

ah ! Got it , thank you !

good point, i have a REV C board in mine, same with his. Ill take a harder look and see.

I tried the steps again to change the AL-5 setting, it would not change, though i can still toggle between Fahrenheit and celsius/metric. i cut power and removed the board, double checked connection, seems fine aside from being a little loose... those plastic legs are not in good shape and...

Its always been loose like that. i am going to see if i can snug it up a bit but its on those plastic legs and the board just snap over the ends.

Yes, change the display to AL-6 the move the switch from auto to super Chlorinate...usually, it doesn't change it in this instance, going to try it again.

I tried that and it did not change, i am going to try it again.

Yesterday "inspect Cell" was on, while i was turning the system off i noticed that the display would flash and "jiggle" a little when i moved the switch or pressed the diagnostic button, seemed like a loose or dirty connection. I took the cell off and started a cleaning in a bucket with diluted...

Update, just before i wrote that post i had removed the switch and used a 240 sandpaper to sand down the contact area on the arm and clean(polish) the contact side of the metal switch arm. turned it on and came in. when i finished the post i went back out, flow light was off and generating...

I am curious, what makes a glx-flo switch go bad in an aquarite? What is the mechanism that closes and allows current flo? Suddenly today i am getting a flashing "no flo" I pulled it and it has some build up grime, ,very fine which i rubbed off with a finger, reinstalled, no change. If i pull...

i handnt yet as i discovered there is a "large hump" tire as well. ($79) This is for application where the unit gets stuck, i may go with these as we have an odd corner and some stoair that occasionally cause issue. https://www.polytecpools.com/05--Pentair-Large-Hump-Tire-Kit-2-tires_p_9128.html

Found a set on Amazon for about 60 bucks , seems reasonable> but wanted to check and see if there were any other options i might not be finding that are better value. Thanks

Im East south East of Phoenix about 25 miles. I have a pentair WhisperFlow: http://i.imgur.com/8sDyw89.jpg single speed 1.5 HP i believe. Ive replaced the motor with a rebuilt about 2 years ago.(Perrys Pool pump Phoenix) I also have one a neighbor tossed: http://i.imgur.com/X5nUUVp.jpg Ive...

Its about 6 or 7 years old, not the original owner of the house, but KNOWS the original owner, may they can get these replaced, how would they do that?

Thanks all for the replies, i have seen the light, staying with the Aqua-rite and replacing the cell(which we found we can use a T-3, so cheaper, correct firmware and pool size of 11k)

very good, i actually found a T-3 for 150 on ebay with a 5 year warranty that looks exactly the same with a 5 year warranty as well, seller is out of Tennesse. (Firmware on the unit is 1.59 so should work, pool is 11k gallons.)

Helping a friend fix a few things with their Shasta pool(phoenix), several of the pop ups are broken and we have been told they are QuickClean #3 . They have two slots. Where do you suggest we can find the best price on these(or comparable/compatible, if there is options). Also, it seems there...

I didn't see a forum specific to ionizers . Apologies if this is in the wrong place. I have and aging aqua-rite system with a salt cell(t-15) that is likely going to maybe make it through summer( #2 cell). Before i purchase a new cell, ive seen some information on Ionizers , and im wondering...

at what terminals/points do i test the voltage/amperage on these units?(T-15)

Reasonable? can you link or offer the best place to buy the t-15 or equivilant? Locally they are 600-800

Edit: Found it an ACE about 15 miles form me.

Need to replace 500LBS and form a thread here it seems HTH is the best sand, BUT i cannot find it anywhere in my area ( Local Ace carries a #20 Silica Sand ). Here is the sand that came out of the filter: i want to make sure what goes in will work best. Several pool stores carry #20 Silica as...

Parts are ordered and on the way, just finished cleaning out the old sand, which i think was likely not the correct sand( perhaps play sand) installed when the unit was first placed( i honestly don't recall if it was me or not). This is mid/low layer sand Anyway, i noticed when vacuuming out...

Solid advice, ill replace parts with OEM. ive found most of this stuff on amazon pretty reasonably priced (relative to LPS) i do think the sun expose had something to do with the deterioration of the head, saw the thread on pool sand and am likely to use the HTH brand. I have in fact used the DE...

Phoenix metro, 11K gallon saltwater 1 HP whisper flow. after 8 years(yeeees without a sand change) my S310T has not been filtering well. Multi-port valve has developed some cracking in several spots as well. I removed the "head" today and found the the down-tube of the distributor was also...

My T-15 lasted just over 6 years in Gilbert AZ( just east of Phoenix). It finally bit the dust last week , i ordered a TI3 Replacement Salt Cell from Pool Express. Installed and working flawlessly, time will tell.

Came across this board looking for prices for a t-15( almost 6 years old, running on a 12K gallon pool) running 6 hours a day on 75% in season, 4 hours on 30% off season, Phoenix area). i was suspicious last summer and had the cell tested at a local store and it indicates "failure",but i still...