Search results

OK so it is working now! This is the longest I have had flow in the last 2 weeks! Once again, thanks for your help! I don't know what I would do without this forum to help me with this pool. Probably fill it in and turn it into a tennis court! Hey why don't you open a branch in the Orlando...

Yes it is one of the new black sensors that came with a daughter board to put on the board in the wall unit. When I hit reset I'm referring to the panel reset button that is just above the time out service and operation button. You have to use a pen to push the little button in and it stops...

No breaks in wires etc. Weird, but I reset the panel at the suggestion from Jandy Tech phone services and when it came off of the waiting cycle everything worked for about a minute then it went back to no flow and the green power button is on and the cell reversing light is on. Is there a way...

Thanks for all of the help with my Jandy Heater problems. The part ignition module came today and it's working! The board in the module where the blower attaches is severely burnt! Until something else goes bad we'll have a hot time in the pool spa!

An old problem has come back again. No Flow with the Jandy Aquapure Handheld and the LCD panel one green light on and no error codes which I used to get in the past. The sensor is only about a year and a half old. The Chlorine cell is about 4 years old. I cleaned the cell (some build up but...

Re: Still having heater problems I think I just got to the bottom of the problem this weekend. As I was going over the votages I got to F1 & F2 on the ignition module and as I was sticking in the probe and smoke came out of the module. I killed the power at the breaker and pulled the module...

Still having heater problems I'm still having Jandy LXI heater problems. The blower doesn't come on, and after about 5 inutes you get a "fault" error "check ignition". I followed a trouble shooting guide and it said the blower motor was bad, it ran on the bench at 110 volt but not 220...

After 5+ years we were just told by the pool store that we have too much calcium in the water. This is a pebbletech finish cement (gunite?) pool. They said to take about a third of the water out and put in fresh. The water is crystal clear, and about 80 degrees. Since we are in Florida...

A local pool store checked it out for me and it ran for him I plugged it back in and no good. I put the VOM probe on the Blue wire and a ground on the unit and get 115volts. If I connect to the white wire and the blue wire with the VOM probes I get nothing. I also get 115volts with any of...

I show power going to the motor from Blue wire and the ground so I'm assuming the motor is the issue but it spins freely, and doesn't show any signs of burn or shorting etc. Is there a way to bench test it to make sure that is the issue? the cheapest I can find the assembly is $387 so before I...

Assuming it is the blower motor (when I get back home I'm going to run it through the troubleshooting guide) how do you get at the blower? It's location was not obvious when I had the front off last weekend.

I have the serial number and model numbers. Theyare Model LXi 250P serial number B08LC1185. I believe it does have a fan in it as I've heard it run before and that was always my clue that it was working. (This has happened once or twice before after it hasn't been used for a while but after a...

I've got a Jandy Aqualink system with a Jandy Propane heater. I'm getting an error code on the heater panel of ignition fault, check ignition. Where do I start with trouble shooting? I took the front panel off and set it to run no fan no sound of an ignition attempt after about 5-10...

The bad reading is on the Jandy handheld wireless device. It is displaying the correct outdoor temperature which I think is coming from a probe that just dangles below the outdoor control panel. Where does the handheld get its reading from? The inline probe? Since there is a salt generator...

Before I order one no one has one in stock, the Jandy control box outside does display the correct temp. Does it get it's read from the probe or from the salt/flow sensor? Thanks,

I have a Jandy Aqua Link system that is about 6 years old. This week the temp in the pool strated reading 177. It really is about 65. Is this a problem with the sensor (looks like it is held into the plumbing pipe from the pump with a clamp) or is there somethig wrong with the Jandy system...

I have a 5 year old in-ground pebble tech pool with a spa LED light and pool LED light (both were 120 volt). THe equipment is Jandy (handheld & electronics, pump and filter) except for the skimmer and LED lights which are Hayward. The pool light died and after much discussion with local pool...

I have a Jandy Aque Link v3.0 and every now and then it just quits working. the pda say "waiting" but won"t connect. I've turned off power at the breaker for a few minutes (even tried overnight once) and nothing. If I take out the screws that hold the top control panel in place and manipulate...

Ping - You are a genius! I went back out and did as you said (and I was able to set the Salinity level at 3.3 which is what the pool store got). The service light is out and the 145 error code is gone! Jandy needs to hire you! You are 100% better than their customer service! You have no...

just tried to recalibrate. I didn't get any beeps whenI pressed the salinity button on the board (the main board not the daughter board). I'll pull the cell and sensor later today and see if it needs cleaned. Just did it a month ago. I did notice two different temperature buttons on the...

Yes we are in St Cloud Florida, and the water temp is around 67 at night up to 73 during the day (we've had a cold spell this last week was up to almost 80 a week ago.

Just to be sure, I did it again. Pressed and held the button on the daughter board until the light went out and came back on again. Still getting 145 error and the Salt reading is 4.4 which is about where it's been. It used to go up and down as the water level went up or down but it doesn't...

Kind of a blackish dark grey color. Definitely not white.

What is the chance that the daughter board or the new trisensor is bad?

Yes, I pressed the button on the new daughter board and still get the same error code and the same salinity reading. I even tried (at Jandy's suggestion) hitting the reset button on the front panel. Still the same results.

I have a Jandy Aqua Pure system and am getting a High Salt General fault on the handheld. The salt is reading 4800 but two pool stores get 3300. I replaced the sensor (for the third time in 5 years) and the new one has the daughter board. The service light is on in the outside panel error...