Search results

Thanks now if I could just figure out why in auto mode it hates the pump running but it's fine is pannel is in service mode or running it from the pump itself.

Awesome Thanks! OK sounds like all is well then, and if at 1200 rpms there is no overflow I guess bonus! Ok so it will not fry the unit? 😃 no cats dogs mass hysteria etc... Thanks again

So the overflow is still good/bad but maybe expected unless the vsp is running at the like rpms of the old pump 3200+ it just cannot get enough pressure in the spa to travel up to the raised spa amd trigger significant overflow. @gkw481anyone with the vsp pump amd automation board, do you know...

Ouch sorry to hear. What have you been doing instead? Today I reset the program speed for speed 2 "medium" to 2500 to match the yellow wire speed ran it for a bit and did not see the issue when yesterday it would not run past 1 or 2 minutes without doing it... not willing to call ot a fix, as I...

Thanks I actually cleaned the filters and continued to brush and vacuum the pool to try and keep it as clean as we could. Still just seems like the volume is less but we did step down from 2 1/2 on the suction side to 2 inch pipes... maybe that's it? It is maybe also worth noting the...

Do you mean on the pump itself? Yes, it was set to manual. What is interesting is that is I leave the breakers off and use start/stop runs flawless. I noticed that speed speed 2 was set to 1500 when I flipped to Program mode or selected speed 2 from manual. I changed the program speed for speed...

Geez, this is a real bummer. Looks like I am not seeing a solution or work around.

Goodness. I have the 3hp B&D and the calimar automation panel hooked up to aqualink and my pump spins up and spins down. Just hooked it up today. I did set the clock, and turning here for advice. 😮‍💨 @Golfer2000 Had You seen any changes or found a solution since January? What is the current...

So just finished hooking it all up thank you all for the ideas and feedback. Here is my final wiring. The pump is directly wired to 240 w/ 20 amp breakers. I flipped the dip switch 3 on for the aqualink pannel to "trick" the box to allowing 2 speed with automation. However I have not really...

Thank you @ajw004 and @gkw4815 much appreciated! The fireman's switch is basically the button on the aqualink pannel, yes? I may need to pull that out and see the guts behind it. However I know I have to hit the heater button to get heat.

Yeah they didn't do me favors in alot of places. However I do have photos of all the pipes before they were buried so maybe I can track them back? Maybe a needle in a hay stack but can try. The 2 middle valves towards the right are the bubblers on the ledge. The left valve and the right are...

Well bummer so even the slower waterflow.. I have an automated divert valve but not sure if it's in the right section or what I need and would need to figure out how what and when to enable that at some point. Thanks for looping and including me in that concept. My Jandy pump died about 2 weeks...

Unfortunately the pool was built to always have overflow from the spa on when the filter pump is on. Aux 3 is the waterfall breaker and we hardly ever use that. Right now all but the 2pd pump which I manually flipped are marked off. My Ph always rises like crazy and I would definitely want to...

Ok did more thought here. Version 4 what do you think? Is 3 or 4 better? Moving the 2 120v w/ the 20 amp breakers to direct wire the new B&D VSP. Then replace the 2 120 lines w/ 20 amp breakers on (Waterfall) Aux 3 with 2 120 w/ 30 amp. Daisy chained the lines to Aux 1 A/B (Spa Bubbler) then...

Ok here is a version 3? Does this look right? Moved the heater and pump to a L1/L2 bundle and bridged then from the line in/breaker or the spa blower. Then run the 5v common to the filter line, and vsp medium to the load. Piggyback the line to line on Aux 2 then white vsp to load, and finally...

So looking at this now I think it will not work. Since the heater piggyback on the aux 2 "booster" and I am not sure where a safe post is for the vsp wiring. I believe the yellow medium should sit on the 2nd laod terminal on the 1st port pool filter perhaps I can link the heater to the filter...

Hello all need someone to help me understand if I have wired this right. Could the helpful experts from the forum let me know if this is sound? Following guidance from here I have wired this up. Thanks @gkw4815 1st my previous wiring: Line came into the spa blower 1st then was carried to the...

Thanks, yes moving to VSP. So I was hoping to keep the 21/2 to offset anything lost by the 2 45 degree elbows. So do you believe they are not doing that, and is the opinion I would not lose much by cutting it off and using 2 inch pipe and 2 in 45 elbows? I'm not a plumber and wanted to avoid...

I have to replace my pump and it seems the builder did not leave me much room. Right now there are 2 1/2 inch 45 degree fittings attached directly to the jandy valve and a short run of 2 1/2 pvc and another 45 to "straighten" it out. If i cut the 2nd fitting off it will shorten the run and...

Thank you for taking the time. Much appreciated

Thanks again. What replay or model did you buy or was used for the other speeds. For example I see 3HP relays. Fo i need those for the 3HP B/D pump? What is confusing to me, is in your diagram it looks like 4 relays, but maybe that is just my misunderstanding. On my panel I have filter pump...