Search results

Onlything metal is the pool wall, top and bottom rails, and top braces...I ran a #6 bare copper from motor to 1 of the bolts where the wall bolts together...

Thanks Alot!

Mine is just laying on the ground right now...We getting some stones to put around pool and then putting some kind of rocks or something on the ground between the wall and stones....

200 pounds was what we first put in.

I bonded a #6gauge solid wire from my motor to one of the pool wall bolts' where the wall bolts together...Can this wire be buried or installed inside of some flexible pvc or should i use solid wire with a coating...I just have it running from the pool back across the ground to the motor...We...

Im getting a little bit of sand back into my pool every day...The paerwork said 175 pounds of sand and the filter shows 200 if im reading it right..Could i have to much sand causing this or could it just be the new sand since its only been running a week..We have backwashed it and cleaned it a...

I picked up 100Ft of the 12/2 UF-B underground wire...I think about 85ft is what i will need..Got the waterproof kit with bubble & GFCI Receptacle...25ft roll of #6 solid copper wire for bonding motor to pool wall...Lowes had the roll on sale...Just wanted to make sure what all needs to be...

Its the 24ft Aqua EZ pool we had the wall and liner problems with ' we talked about on another topic...I see where some used one of the bolts where the wall bolts together ' to bond the motor to the wall...So ur saying just use the ground from the house to the GFCI Receptacle' then to motor with...

We have a new pool installed and just needed to know what size/type wire was needed for my setup... 115V Motor 60Hz 9.5 Amps Between 75-80 feet from inside house breaker box and pool... I have seen a few install the 1/2 8ft long ground rods and bond the pool /motor and back to the GFCI...

Humidity has been real bad here this year' with also higher than normal temps...Onlything strange is it just goes around about 6ft or so only...I guess i could try the bucket test. The dealer said they have never had 1 liner to come back with a bad seam...Its been real dry but now its raining...

We have just installed a new pool and was very careful with every step and know the liner was not harmed..We only have about 3-5 inches of water in the pool' havent realy noticed a water drop...But we noticed the thin layer of crushed limestone around the pool was damp from water...We have foam...

You know anyone that has a video or pics of the easiest way the top brackets and rails to to be installed' after the liner is ready and in place...Evrything i find skips that part ... I just talked to bill at Aqua EZ and he said it would be fine for the wall part of the liner to rest on the...

I couldnt talk to them over the weekend' but waiting on a call from them today..I left a voice message yesterday..Bill i talked to there was realy nice and had already replaced a damaged wall at no charge the week b4...We just trying to get this finnished b4 the rain comes back... ps: is their...

Yeah' we used blocks when i set up the bottom support rail to keep it from moving' and we had it 24ft perfect...After the wall was installed ' the ends were only 1/4 inch off..We remeasured the pool and its still right at 24....So ur saying it dont hurt for the side of the liner to sit down on...

I can post some pics if it will help...Its a foot short the direction that the seams run on the bottom....Its 24 ft the other direction...We waited till the sun came back out yesterday and tryed getting the liner to reach the wall ' but it only stretched maby 1 inch or less after the sun hit...

We are installing a new pool and liner, the pool walls are completely level and at 24 foot. The liner however is 24 foot one way and the other way is 23'1". The 23'1" is the direction the seam runs, there are no wrinkles this direction. Why is it to short that direction?