Search results

  1. U

    PebbleSheen (PebbleTec) finish issues

    Thanks. Too bad they will not consider calling me back to re-plaster.
  2. U

    PebbleSheen (PebbleTec) finish issues

    I have an issue with my Pebble Sheen (Pebbletec) finish. This occurred after the big freeze in Texas and my hot tib was cycling through freeze protection. Snow and ice coated the finish. Centex Plaster the only Pebbletec group in Austin will not even return my call after trying for months...
  3. IMG_3210.jpg

    IMG_3210.jpg

  4. IMG_3208.jpg

    IMG_3208.jpg

  5. IMG_3209.jpg

    IMG_3209.jpg

  6. IMG_3207.jpg

    IMG_3207.jpg

  7. IMG_3206.jpg

    IMG_3206.jpg

  8. U

    Freeze damage - pebble coating chipping?

    Following. I noticed the same chipping in my spa. The freeze protection tends to lower my spa water and the pebble sheen was exposed to below freezing temperature with ice and snow on it. I assume the freeze caused the chipping. I contacted the plaster installer and am waiting for them to...
  9. U

    Ichlor vs. Intellichlor

    Thanks. It is about 8 years old. I already replaced the flow switch a year or 2 ago. I think it just might be time to replace.
  10. U

    Ichlor vs. Intellichlor

    I have a few questions on the Ichlor. I search the forum and could not find answers. I need to replace my IC40 and I am considering the Ichol 30. I have a 19,000-gallon pool with a UV light sanitizer. Is the Ichor the latest Pentair SWG? I saw a few youtube videos saying that? Does anyone...
  11. U

    First cartridge filter flush

    I use this one. It works great. Takes less than 30 minutes to clean 4 of them. https://www.amazon.com/Mi-Way-Aquacomb-Filter-Cartridge-Cleaner/dp/B00818KY0Y
  12. Screen Shot 2018-04-30 at 8.46.52 PM.jpg

    Screen Shot 2018-04-30 at 8.46.52 PM.jpg

  13. U

    What have you found in the skimmer basket?

    Worse thing I found is a baby rabbit. Also had a coral snake. Sent from my iPad using Tapatalk
  14. U

    Stenner Pump Wiring to EasyTouch Relays

    Jim, I am able swap out Stenners and get the 220. I appreciated all the help. I guess I was just testing your knowledge. [emoji3][emoji106] Looks like I will be back to your original drawing. Thanks a ton for you help. Now I just have to wait for the exchange. Let me know if the...
  15. U

    Stenner Pump Wiring to EasyTouch Relays

    Thanks. I hope to work on it next weekend. I will check to see if I can swap out Stenners.
  16. U

    My WaterPots (fountains) are dry

    Jim. Got it thanks. Eventually I will figure this pool plumbing thing out.
  17. U

    Stenner Pump Wiring to EasyTouch Relays

    Jim, Thanks. I think I got it. I assume you meant upper left relay is the pump. Picture came out rotated negative 90. One question is neutral bar. Do you mean the connected group of white wires? Best, Eric
  18. U

    My WaterPots (fountains) are dry

    Thanks all. I do not think it is a leak. My valve position have not changed at all. Sounds like it might be a check valve. Where might they put a check valve? It is probably better they drain back into the pool. I now have less squirrels drinking out of them and birds playing in them I...
  19. U

    My WaterPots (fountains) are dry

    I have some water pot that are on a separate single speed pump. The pump runs these and a bubbler. They used to always have water in them however now they are always dry see the picture Running After running Could it be a leak? Sent from my iPad using Tapatalk
  20. U

    Stenner Pump Wiring to EasyTouch Relays

    Thanks. I finally was getting around to install it. However, I forgot my Itellitouch was original an EasyTouch 4 and it looks like I am missing relays. Pentair replaced it right the build due to some issues. Attached is a picture of the inside of my unit. So my question is: Do I need...
  21. IMG_5927.jpg

    IMG_5927.jpg

  22. IMG_5926.jpg

    IMG_5926.jpg

  23. U

    Stenner Pump Wiring to EasyTouch Relays

    Jim, Thanks. So can I wire an outlet into that relay grabbing power from my GFI. I prefer to leave the pump plug in place. Eric
  24. U

    Stenner Pump Wiring to EasyTouch Relays

    I have Stenner 120V, what is the way to wire to the Intelitouch panel. I assume I cannot do like the diagram because of 120v. I have the same setup as robbief00. Thanks EL
  25. U

    Water Pots are dry

    I noticed that my Water Pots that use to always have some water in them are dry. When I run them they seem to work fine. They fill up and then are bone dry the next day. They used to always have water in them. Any suggestions?
  26. U

    Cement board screws?

    I used Parex per his suggestion as well. It is simple. I got a drywall hopper for my compressor at Harbor Freight and used that to apply it. It could not have been easier. I put two coats on.
  27. U

    My Outdoor Kitchen is Complete!

    As of now all is dry in the storage. Had some big rains earlier. The granite top with silicon caulk around drop-ins is water tight. Initially had water splash through the doors since they are not water tight. I put some weather striping on the inside that took care of this problem. I think...
  28. U

    My Outdoor Kitchen is Complete!

    Thanks. The Kamado is a Kamado Joe Classic grill. It is awesome. Very happy with it. Use it all the time - used the gas grill only once since the build. No, under the hatch is a built it Ice Chest/Cooler. The side burner is next to the grill. Also put an umbrella sleeve in the middle of...
  29. U

    My Outdoor Kitchen is Complete!

    Granite and Bling!!! [attachment=2:1ckv7qhv]IMG_1045.JPG[/attachment:1ckv7qhv] [attachment=1:1ckv7qhv]IMG_1046.JPG[/attachment:1ckv7qhv] [attachment=0:1ckv7qhv]IMG_1047.JPG[/attachment:1ckv7qhv]
  30. IMG_1047.JPG

    IMG_1047.JPG