Search results

He has a suction cleaner. If running with to many rpms will cause a suction side restriction which cause the pump to lose efficiency draw more watts also causeing the pump to over heat. Over heating the pump can cause the impeller to warp and cause a pump seal leak. Pump seal leaks over time...

Jet spa hayward หัวเจ็ทสปา By winwin pool - YouTube...

Honestly, I do not like 2 speed pumps and I'm pro vs pumps. Intelliflo is always my go to pump. If you do go that direction make sure you get a flow meter ( fits in return has a white plate and spring) so you can adjust your rpms for your suction cleaner correctly so you don't damage your pump.

Having alot of complaints from my customers with apple products and screen logic not working correctly. Pentair might just have to update there app.

Ring return ring then the piece that screws in to secure the return.

If you go to fire your heater up and then when gas valve opens up and then you hear fast repetition of clickng then you will need a regulator on your gas line. That gas pressure might break your gas valve.

Do you have an ozanator installed on your system?

If you have any unused auxs, then just assign a high speed on one of them and name it. That way when ever you turn that aux on you'll get the pressure you want.

Sounds like a short in the drive. I would contact pentair and see if there is any warrenty first. If not then the motor and drive are 1 part. So replace that the orings and pump seal.

Pentair clean clear plus 420 is good for 20 and under. With your 1.5 hp pump and 12 pool, I think that would be ideal.

Might have a crack in the volute, honestly with it being 17 years old and since that pump is discontinued, I would suggest replacing it with a new pump.

Hey no problem, I've been in this industry for most my working career. Got plenty of tricks up my sleeve if you ever want to pick my brain.

Get a seat removal tool. Basiclly there are 2 slots in that return. Your put the tool in the slots the screw it off (lefty losely ) then screw in the return Hayward Eyeball Seat Removal Tool SP1419T | Above Ground Pool Closing

Hey I would go for the pentair ultra temp heat pump. It will cool your pool down pretty well. Do not get a Glacier. Pools in tx get uncomfterablely warm in the summer and glaciers cant cut it.UltraTemp High Performance Heat Pump - Pool and Spa Heaters - Pentair

Hey, with your clean clear and plus cart filter, when depressurizing and removing your cartridges some times debree will go into your manifold and get stuck into your intellichlor (salt cell) So I would suggest to check your salt cell for blockage.

You want to use a fitting extender. You can cut that garbage flex line Off and this fitting fits over your coupling. Just make sure you give plenty of time to let the glue cure. And if you go the next size up a coupling should fit over the check valve. MagicMend® Extender Fittings - Magic...

On your old port sensor it plugged into a small little chip that was plugged into the board. If you plug your new Port sensor into that little board then it won't read flow. Remove the board and plug your sensor where that board was plugged into.

Ichlors have an issue and are not a good product. The tops arn't completely sealed and allow water in to the bored and short out. I warrenty pentair products and we were told buy our warrenty manager to replace Ichlors for ic-40

Sound like a flow sensor for the ic -40. Since you're under warrenty contact pentair for a warrenty call, then they will contact a close company that is certified in pentair products and does pentair warrenties.

If its a aqualogic ps-8 you shouldn't have to replace the display the keypad and your should be good to up grade it. I've replaced many aqualogic boards for prologic boards with out any issues as long as they are ps-8. The keypad should fit the stands but the red wire in the upper right will...

Omni logic doesn't communicate right with intellibrites. I would suggest with a pentair automation with the ic-40 and intellibrites. But do remember to get a surge protector on your sub panel as pentair doesn't have any protection aganst surges built in to their system. The surge protector...

Bad Main pcb board on your aquarite power center sounds like its your issue. Take off the cover to your power center and check the top middle right for a resister that looks like a black disc sticking out on to wires out of the board. If you see a crack on that disc then that is exactly your...

I think you are looking for the pdf for a microclear hay de filter. https://hayward-pool-assets.com/assets/documents/pools/pdf/parts-diagrams/MicroClear.pdf?fromCDN=true does that help?

Main power goes to line 1 and line 2, the wires for pump goes to load 1 load 2.

Pressure gauge could be bad or bent. If the dial is bent foward the need gets stuck.

Un screw the sight glass, clean off the algae and screw it back in. Don't forget about the oring. Left lose. Right tight.

Re: Dirty water in return jets Do you have a variflow or selectaflow multiport?

What kind of filter do you have?

They are water way 90 sweeps 2". You can check them out at waterway plastics. I can tell by looking at them is by how deep the insert is where you glue the pipe into the fitting. DWV insert is about 1 1/2" deep while schedule 40 is about 3" deep. (Don't quote me on those measurements lol)...

Carburetor cleaner will take off the residue in your chlorniator. Get one with a small straw and in a pressurized can. It is strong stuff so don't get it on the check valve or screen and rinse it off when you're done.