Search results

My neighbor has a Swim Pure Hayward SWG. When he firsts turns it on, the red flow light flashes. When the flow is restored the light goes out and NO lights are on. Readings: 4300 0 100p 0 AL-2 r 1.40 What's up? Thanks

I don't have a heater and was thinking maybe adding MA to the skimmer when necessary will cut down the times I would have to soak the Salt Cell. Crazy?

Any tips on starting up after they apply the Stone Scapes Mini Pebble? (I refused the $700 start up service).

1.5hp at 3,000rpm or 3.0hp at 1,500rpm

The Swim Pure control box display reads "Cold" and the green Generating light is blinking. The water is 82 degrees. The cell was just cleaned. What's up?

It's my neighbors pool.... The red light reads "check salt" (my Taylor kit measures 3600ppm). The green "generating" light is on. The readings are: 2900 84 24.7 5.6 / 5.7 (on then off then on) 2900 If the "generating" light is on will it produce chlorine even though the "check salt " is on?

My neighbor just resurfaced their pool with Pebble Tec. They previousy had a Barracuda G3. There is a lot to like about that cleaner. The Pebble Tec installer said it would mar the finish. Is this true?

Is there a way to test the flow switch. I unscrewed it and touched the 2 pieces together and expected the control box "red light" to go off. It didn't.

Does keepping the FC level a little higher (6-8ppm) fade inground vinyl pool liners faster than lower level (3-5ppm). Assuming no algae grows at the lower level?

Does it seem unusual to need 7 lbs. of Stabilizer twice per year to maintain 60-70ppm? The pool is 35,000gal. Thanks

Will a pool's salt concentration measure differently if the water is 30 degrees warmer or colder?

I think I have a good handle using the TFP methods of maintaining a pool. Is there anything different with a SPA? My neighbor has the SPA and been using Bromine and ozone etc. and having trouble. I'm a Liquid Chlorine and Mauratic Acid guy. Can we just drain it and use the basic TFP procedures?

My cell is flashing a green light in CELL area of the STATUS section. The manual says that it is not generating and to inspect the cell. My question is; inspect the cell for what? It is very clean and registers that it is 20% used. What is my next step? Thanks!

Is there any "evidence" that a generic flow switch is any better or worse than the Pentair? Thanks

If the white wire from the flow switch is cut/broken what is the display result?

Does this serial number tell when the cell was manufactured? 000040020314

https://www.ebay.com/itm/Pentair-Intellichlor-IC40-Salt-Cell-Brand-New-in-the-box-FREE-SHIPPING/193104956555?hash=item2cf5f3cc8b:g:RuIAAOSwV8ZdgX9Y

My neighbor has a Hayward Swim Pure T-15. When he replaced the cell, the genaeric recorded 4900ppm Salt while the Taylor K-1766 showed 3600ppm. The lights indicated everthing was working and it was really generating Chlorine. He could cut the production down by 30% from the previous OME cell...

I have a Pentair IC 60 that just started flashing a green light in the check salt area. The Taylor K-1766 shows 3600ppm It has a between 1,000 and 2,000 hours of use. It was just cleaned and I replaced the flow switch. The flashing continued. What do you think? Thanks

My neighbor has a Hayward Aqua Rite T-15 that I try and help him with. It is displaying the salt level at 4500ppm on instant and average. The Taylor test kit shows 3600ppm. It is not flashing "high salt". All the other diagnostic readings are good. I usually see the display reading lower than...

Will more salt (say 4,000ppm) produce more chlorine gas than (say 3,000ppm) if the controller is set to 100% for each?

Is it possible for all the lights to be solid green, set to 100% and the cell be worn out and not producing? Manufactured in 2013. It shows 8,000 hours of use.

I've run into a neighbor's Hayward Swim Pure with a Hayward t-15 cell that flashes "check salt" daily. The display shows 2000. Instant salt reading is 3200. Taylor K1766 says 3000. I scroll to the instant salt reading (3200) and then to "super chlorinate" and back to "auto". The average...

Could this Hayward flow switch be used with a Pentair SWG? It looks so similar. A little splicing and a fella could save $40...

I ran into an IC 60 today with the following situation: SALT LEVEL.....Solid Green STATUS....... No Lights FLOW......Solid Green SANITATION OUTPUT.......All Lights Flashing Green The cell is clean and when I push and hold the MORE button, no lights come on, then back to all flashing green...

The "Inspect Cell" light is continuously flashing. It is very clean on the inside. How do I get the light to go off? Thanks

Is it important to get the pool water above 60 degrees to get an accurate Salt reading with the Taylor K-1766?

With a Hayward Swim Pure, is it possible to have both top two lights (Power & Generating) to be GREEN and the water be too cold (53) for it to be producing chlorine? I have had it running 24/7 for 3 days and losing 1ppm per day. No other lights are lit.

When I press and hold the "more" button, no lights come on. 10,000 hours remaining? It's very clean. Now to the problem..... It was manufactured in 2013 but I don't think it was ever used. I hooked it up today and all the lights came on as they should but after a couple of minutes the "Salt...

Except for the wiring, are the 2 flow switches interchangeable?