Recent content by NewbieForeva

  1. N

    After Algae, can't get cloudy water to clear

    I have algae problem and then I dump a bunch of dry chlorine into the pool and now the algae seem to be gone after a week. However, my water is still cloudy after dumping chlorine, below is detail of what I did To kill the green algae, 4/25 I added about 5 lbs of DryTec Calcium Hopychlorite...
  2. N

    First time Pool Owner

    Can someone please post a picture of the chemical Cyanuric ACid that you guys used to raise the CYA level? My CYA level is at 0 right now. Is there a certain brand name or stablizer product that is recommended to raise CYA level? From what I read, the stabilizer is a powder product? Do I...
  3. N

    Pump Voltage...125 or 220?

    You might want to check your power wiring.
  4. N

    Skimmer suction

    Interesting, I am having the same problem as you have.
  5. N

    First time Pool Owner

    I'm not sure what's a good CYA level it should be for my pool. The reason I say it's low because on the CYA chart, it start with 60 so I figure mine is low. Do you supposed to lose FC level after a rain? If so, how much FC do you lose after a rain?
  6. N

    First time Pool Owner

    Hello all, I'm back with question regarding to chemical My current test result TA - 100 pH - around 8 FC - 1.5 CYA -45 -50 My CYA level drop from about 90 to 50 the last 2 months. What do I need to add to raise my CYA level up since 50 seem a bit low.
  7. N

    Wiring Hayward Prologic PS-4 (or OmniLogic) Sub panel

    What is the size of your 2 current breaker right now at the main breaker? Do you know what wire size are you running from your main breaker to the pool right now? Can you change your main breaker to a 240V breaker and using your existing wire for the 2 legs to run 240V to your prologic...
  8. N

    "waterproof" LED strips around the pool edge?

    I'm looking to run these IP65 LED waterproof strip on Ebay around the edge of my swimming pool and water fountain. The wire that supplied 24V power to the strip is going to be a few feet away from the pool. I really don't see a shock danger from doing this. Will post some pictures once my...
  9. N

    First time Pool Owner

    I added 3lbs at first base on the specification of the Filter manufactured, which I think was correct. However, I was going through my previous owner supplies and equipment, I saw a note to add 6lbs so then I decided to added more but then I thought about it and stopped. I should have...
  10. N

    First time Pool Owner

    I can probably get someone to do it for sure. However, I'm a control system specialist for oil and gas industry by day so I don't see why I can't get this running by myself, I rather learn how to install it and able to maintain it in case anything happen. The picture just help me understand...
  11. N

    Prologic PLPS4 or PLPS8

    According to the manual, The connection at the main house panel should be to a 240VAC circuit breaker rated at 100A maximum. I am going to have an existing 40A breaker main house connections that feed PLPS8 main powers. Can someone confirm my 40A breaker would be fine?
  12. N

    First time Pool Owner

    According to the manual, the ideal pool water "Free Chlorine 1 to 3 ppm". So if my CYA level is at 60 and my FC target is 7, isn't that high compare to the Hayward?
  13. N

    First time Pool Owner

    Ok I decided to go with a used Prologic PLPS8. If anyone had one please take a picture of the wiring inside the panel so that I can study it and wire my pool equipment to it. Thanks
  14. N

    Prologic PLPS4 or PLPS8

    Does anyone owned a Prologic PLPS4 or PLPS8? If you do, can you please give me a picture of the inside of the panel so I can study how to wire my stuff up once I have the money to buy a controller? Thanks
  15. N

    ProLogic vs OmniLogic

    I'm interested in Prologic PLPS4, how much will you give them to me for?
See more
Top Bottom
Back